User manual MTD 25HP

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual MTD 25HP. We hope that this MTD 25HP user guide will be useful to you.


MTD 25HP : Download the complete user guide (841 Ko)

Manual abstract: user guide MTD 25HP

Detailed instructions for use are in the User's Guide.

[. . . ] Hydrostatic Zero-Turn Commercial Riding Mower Professional Turf Equipment MODEL 25HP Tank 53AB5BAX150 53AB5DCX150 OPERATOR’S AND SERVICE MANUAL TABLE OF CONTENTS Foreword. 27 Warranty This product may be covered by one or more of the following patents: D409, 208; 5, 946, 894; 6, 070, 690; Pending 2 FORWARD The 25HP Tank Hydrostatic Zero-Turn Commercial Riding Mower provides superb maneuverability, mid-mount cutting capability for professional landscapers, commercial lawn service companies, professional turf managers and golf course superintendents. The machine incorporates many safety features that should be studied by all operators and maintenance personnel before use. This manual presents all of the operating and maintenance instructions necessary to keep your mower at peak efficiency. [. . . ] If the blade dips on one end, file stock off of the cutting surface on that end. Note: Blades that cannot be easily balanced—REPLACE. 3. WARNING: Never mow with dull blades!Wrap the cutting surface of the blade with a rag to avoid injury. Changing the Blade Drive Belts: a. Using a 1/2" socket breaker bar or socket rachet insert the male end into the 1/2" opening in the lower idler arm assembly and pull the idler arm clockwise. While holding the idler arm back, loosen the blade drive belt from the pulley and slide the belt away from the pulley. Loosen the belt retaining bolt. 15 Cover Plate Spindle Figure. Pull the tensioner pulley away from the belt and remove the PTO belt then remove the blade drive belt. Reverse the process to install the belt. Hydraulic Tank Note: When replacing belts do not overtighten. Adjust the idler pulley so that a tenpound pull with a spring scale between two pulleys deflects the belt about 1/2". Adding Hydraulic Oil (use SAE20W 50) Place the Mower on a level surface and engage the parking brake. Pour hydraulic oil into the reservoir up to the lowest hole in the oil tank fill neck, if necessary. Jack up the front of the mowing deck about one foot and block it in that position. Using a wrench or socket rachet remove four hex nuts, and the four hex head cap screws. Draining Hydraulic Oil Used hydraulic oil must be disposed of properly. Do not pour it down a drain or sewer, or dump it on open land, this creates an environmental hazard. Please be aware of the environment when disposing of used oil. B. Hydraulic Oil WARNING: Never overfill the hydraulic units. Damage can occur if the oil level is not within the proper operating range. Note: When adding hydraulic oil, do so in small quantities and recheck the oil level before adding more. Place a suitable container (at least 2 gallon) under the hydraulic reservoir and filter. Remove the drain plug from the bottom of the hydraulic oil tank to drain. Remove nut 16 caps and drain oil from both left and right pumps. Replace and retighten nuts. Hydraulic pumps c. Store the battery with a full charge. A discharged battery will freeze (refer to the table below). Specific Gravity 1. 265 1. 250 1. 200 Figure. 9 Unfasten hose and drain from this side of both pumps. Freezing Temp (°F) -71 -62 -16 5 16 1. 150 1. 100 Coat new filter seal with oil before installation. Add proper amount of hydraulic oil to reservoir and repeat step L. j. d. [. . . ] To raise the deck: remove the shoulder bolt mounting the height of cut link to the lift handle and reassemble the shoulder bolt in the lowest of the three holes. To lower the deck: remove the shoulder bolts mounting the height of cut link, flip the height of cut link around and reassemble the shoulder bolts in the top of the set of three holes and the bottom hole. 12) Height of Cut LInk Eyebolt Point B Eyebolt Point D Point A Jam Nuts Figure. 12 Point C 26 WIRING DIAGRAM 27 MAINTENANCE RECORD DATE WORK PERFORMED DATE WORK PERFORMED 28 MAINTENANCE RECORD DATE WORK PERFORMED DATE WORK PERFORMED 29 MAINTENANCE RECORD DATE WORK PERFORMED DATE WORK PERFORMED 30 MAINTENANCE RECORD DATE WORK PERFORMED DATE WORK PERFORMED MANUFACTURER’S LIMITED WARRANTY - TURF EQUIPMENT This warranty is specific to the product manual to which it is attached. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE MTD 25HP




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual MTD 25HP will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.