User manual MTD 21BK410G163

[. . . ] Operator’s Manual Since it began making garden tools in 1850, Bolens has been known for longlasting, dependable products. Bolens eventually carried that hard-working heritage into the outdoor power equipment industry, when it designed and built the first-ever power-driven garden tractor. Today, homeowners around the country rely on Bolens for durable, reliable power equipment at an affordable price. 2-Cycle Garden Cultivator Model BL410 INTRODUCTION THANK YOU Thank you for buying this quality product. [. . . ] With the engine running and the tines off the ground, depress the throttle control to increase the engine speed. Holding both of the handlebar grips firmly, slowly lower the cultivator until the tines make contact with the ground (Fig. As cultivating action begins, pull back on the cultivator so that the tines can penetrate the ground. Once the ground has been broken, continue at a moderate pace until you are familiar with the controls and the handling of the cultivator. Pull the cultivator backwards to improve the depth of cultivation and reduce your effort. WARNING: To prevent serious personal injury, use extreme caution when reversing or pulling the unit towards you. If the tines are digging too deep or not deep enough, adjust them according to Adjusting Tine Depth. ADJUSTING TINE DEPTH Tine adjustment will vary depending on the type of soil being cultivated and how it will be used. Generally, adjusting the tines to break the soil 4 to 6 inches is recommended for most gardens. Slide the wheel bracket assembly down for shallower penetration, and up for deeper tine penetration. Once the tines are in the desired position, tighten the wing nuts, making sure that the carriage bolts are seated properly through the bracket. 10 Up Down TRANSPORTING THE UNIT WARNING: To prevent serious personal injury, always stop the engine when operation is delayed or when transporting the unit from one location to another. 9 10 MAINTENANCE & REPAIR INSTRUCTIONS MAINTENANCE SCHEDULE Perform these required maintenance procedures at the frequency stated in the table. NOTE: Some maintenance procedures may require special tools or skills. If you are unsure about these procedures take your unit to any nonroad engine repair establishment, individual or authorized service dealer. WARNING: To prevent serious injury, never perform maintenance or repairs with unit running. FREQUENCY Before starting engine Every 10 hours Every 25 hours Every 50 hours MAINTENANCE REQUIRED Fill fuel tank with fresh fuel mix Clean and re-oil air filter Check and clean spark arrestor Check spark plug condition and gap Inspect exhaust port and spark arrestor screen for clogging or obstruction to assure maximum performance levels NOTE: Maintenance, replacement, or repair of the emission control devices and system may be performed by any non-road engine repair establishment, individual or authorized service dealer. In order to assure peak performance of your engine, inspection of the engine exhaust port may be necessary after 50 hours of operation. If you notice lost RPM, poor performance or general lack of acceleration, this service may be required. If you feel your engine is in need of this inspection, refer service to any non-road engine repair establishment, individual or authorized service dealer for repair. DO NOT attempt to perform this process yourself as engine damage may result from contaminants involved in the cleaning process for the port. REFER TO Page 8 Page 12 Page 12 Page 13 Page 12 TINE REMOVAL AND REPLACEMENT Replace all four (4) tines at the same time, because they will wear evenly through normal use. [. . . ] MANUFACTURER’S LIMITED WARRANTY FOR: The limited warranty set forth below is given by Troy-Bilt LLC with respect with new merchandise purchased and used in the United States, its possessions and territories. Troy-Bilt warrants this product against defects in material and workmanship for a period of two (2) years commencing on the date of original purchase and will, at its option, repair or replace, free of charge, any part found to be defective in material or workmanship. This limited warranty shall only apply if this product has been operated and maintained in accordance with the Operator’s Manual furnished with the product, and has not been subject to misuse, abuse, commercial use, neglect, accident, improper maintenance, alteration, vandalism, theft, fire, water or damage because of other peril or natural disaster. Damage resulting from the installation or use of any accessory or attachment not approved by Troy-Bilt for use with the product(s) covered by this manual will void your warranty as to any resulting damage. [. . . ]