User manual MTD GT2186-44

[. . . ] OPERATOR’S MANUAL SERIES 2000 TRACTOR Model Number GT 2186-44 w/44" Mower Deck IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLY Warning: This unit is equipped with an internal combustion engine and should not be used on or near any unimproved forestcovered, brush-covered or grass-covered land unless the engine’s exhaust system is equipped with a spark arrester meeting applicable local or state laws (if any). If a spark arrester is used, it should be maintained in effective working order by the operator. In the State of California the above is required by law (Section 4442 of the California Public Resources Code). A spark arrester for the muffler is available through your nearest engine authorized service dealer or contact the service department, P. O. [. . . ] Remove the oil filler cap from the left valve cover and SLOWLY pour in oil. Fill the crankcase until the oil level reaches the “FULL” mark on the dipstick (Refer to Figure 18). Reinstall the oil filler cap by screwing it securely into the valve cover. NOTE The oil filler cap MUST BE TIGHTENED SECURELY INTO THE VALVE COVER AT ALL TIMES WHEN THE ENGINE IS OPERATING. Start the tractor engine and allow it to run for 30 seconds, then stop the engine and remove the ignition key. Check the oil filter and drain valve for leaks. 25 CHECKING TRANSMISSION OIL LEVEL Refer to the LUBRICATION TABLE for information regarding the proper type of oil to add to the transmission case. Clean the area around the oil fill plug/dipstick to prevent debris from entering the transmission case. Remove the oil fill plug/dipstick from the oil fill port and SLOWLY pour oil into the oil fill port. Fill the transmission case until the oil level reaches the “FULL” mark on the dipstick (Refer to Figure 20). Reinstall the oil fill plug/dipstick securely into the oil fill port. NOTE Check the oil level only while the engine is stopped and the tractor is level. Check the oil level of the transmission case before each use to see that it is filled to the correct level. Before checking the transmission oil level, clean the area around the oil fill plug/dipstick to prevent debris from entering the transmission case. Always keep the oil level between the “FULL” and the “ADD” marks on the dipstick (See Figure 20). When checking the oil level, the dipstick must be withdrawn and wiped clean, then inserted all the way before being withdrawn for a true reading. CAUTION OPERATING RANGE The oil fill plug/dipstick MUST BE INSTALLED SECURELY INTO THE FILL PORT AT ALL TIMES WHEN THE ENGINE IS OPERATING. TRANSMISSION DIPSTICK HYDROSTATIC DRIVE OIL FILTER CAUTION Never overfill the transmission case. Damage may result if the oil level in the transmission case is below the “ADD” mark or over the “FULL” mark of the dipstick. Figure 20 ADDING TRANSMISSION OIL NOTE For best results, fill to the “FULL” mark on the dipstick as opposed to adding a given quantity of oil. Refer to the MAINTENANCE CHART for information regarding the frequency of the hydrostatic transmission oil filter replacement. The filter can be obtained through your Cub Cadet dealer under the part number 923-3014. Refer to the LUBRICATION TABLE for information regarding the oil capacity and the proper type of oil to pour into the transmission case. Stop the tractor engine and remove the ignition key. CAUTION Never overfill the transmission case. Damage may result if the oil level in the transmission case is below the “ADD” mark or over the “FULL” mark of the dipstick. NOTE For best results, fill to the “FULL” mark on the dipstick as opposed to adding a given quantity of oil. Always check the level on the dipstick before adding more oil. 26 2. Clean the area around the transmission drain plug to prevent debris from entering the transmission case. Remove the drain plug and allow the transmission oil to drain into a clean container having a capacity of more than 6 quarts. [. . . ] After three months, the battery replacement credit is based on the months remaining in the twelve (12) month period dating back to the original date of sale. Any replacement battery will be warranted only for the remainder of the original warranty period. All belts are covered by a one (1) year limited warranty against defects in material and workmanship. This limited warranty does not provide coverage in the following cases: a. Routine maintenance items such as lubricants, filters, blade sharpening, tune-ups, brake adjustments, clutch adjustments, deck adjustments, and normal deterioration of the exterior finish due to use or exposure. [. . . ]