User manual MSI WIND TOP AE270-004EU

[. . . ] AE270/ AE2712 Series All-in-One (AIO) PC MS-AF11/ AF12/ AF16 System G52-AF161X4 Preface Contents Copyright Notice iii Trademarks iii Revision iii Upgrade and Warranty iv Acquisition of Replaceable Parts iv Technical Support iv Green Product Features iv Environmental Policy v Chemical Substances Information v Battery Information v Safety Instructions vi CE Conformity viii FCC-B Radio Frequency Interference Statement viii WEEE Statement viii 1. Overview 1-1 Packing Contents 1-2 ii System Overview 1-3 Component Replacement & Upgrade 1-9 2. Getting Started 2-1 Safety & Comfort Tips 2-2 Hardware Setup 2-3 3. System Operations 3-1 On-Screen Display (OSD) (Optional) 3-2 On-Screen Display (OSD) (Optional) 3-5 Power Management 3-8 Network Connection (Windows 7) 3-10 Network Connection (Windows 8. x) 3-13 System Recovery (Windows 7) 3-16 System Recovery (Windows 8. x) 3-26 A. [. . . ] Go to [Start] > [Control Panel] > [System and Security]. Then click on the [Power Options] link. You may also fine-tune the settings by clicking [Change plan settings]. All-in-One PC ■ The Shut Down Computer menu presents the options of Sleep (S3/S4) & Shut Down (S5) for rapid and easy management of your system power.  Power Management through ENERGY STAR qualified monitors (Optional) The power management feature allows the computer to initiate a low-power or “Sleep” mode after a period of user inactivity. When used with an external ENERGY STAR qualified monitor, this feature also supports similar power management features of the monitor. To take advantage of these potential energy savings, the power management feature has been preset to behave in the following ways when the system is operating on AC power: ■ ■ Turn off the display after 15 minutes Initiate Sleep after 30 minutes  Waking the System Up The computer shall be able to wake up from power saving mode in response to a command from any of the following: ■ ■ ■ ■ the power button, the network (Wake On LAN), the mouse, the keyboard. 3-9 ■ ■ ■ ■ Turn off the monitor by pressing the LCD power button after a period of user inactivity. Tune the settings in Power Options under Windows OS to optimize your PC’s power management. Install power saving software to manage your PC’s energy consumption. Always disconnect the AC power cord or switch the wall socket off if your PC would be left unused for a certain time to achieve zero energy consumption. Energy Saving Tips: System Operations Network Connection (Windows 7)  Wired LAN 1. Select [Connect to the Internet] under [Network and Internet]. 3-10 3. Select [Broadband (PPPoE)] to connect using DSL or cable that requires a user name and password. 4. Type the information from your Internet Service Provider (ISP) and click [Connect] to establish your LAN connection. All-in-One PC  Wireless LAN 1. Select [Wireless] to connect using a wireless router or a wireless network. 3-11 4. Choose a connection from the list or click [Open Network and Sharing Center] to establish a new connection. System Operations 5. To establish a new WLAN connection, select [Set up a new connection or network] in [Network and Sharing Center]. 6. Followingly, choose [Manually connect to a wireless network] and click [Next] to continue. 3-12 7. Enter information for the wireless network you intend to add and click [Next] to proceed. Click [Close] to exit or select [Change connection settings] to modify the WLAN settings. All-in-One PC Network Connection (Windows 8. x)  Wired LAN 1. Select [View network status and tasks] under [Network and Internet]. 3-13 3. Select [Set up a new connection or network]. System Operations 5. Select [Broadband (PPPoE)] to connect using DSL or cable that requires a user name and password. 7. Type the information from your Internet Service Provider (ISP) and click [Connect] to establish your LAN connection. 3-14 All-in-One PC  Wireless LAN 1. Select [Settings] on Desktop, locate a wireless icon with available network. 2. To establish a new connection, select [Network and Sharing Center] under [Network and Internet] in [Control Panel]. 4. [. . . ] Check if the system is connected to an electrical outlet and it is turned on. Check if the power cord and all cables are connected firmly. When I turn on my computer, the message “Operating System not found” appears or Windows does not start. 1. Check if there is a non-bootable CD/ DVD inside the optical disk drive. Check Boot Device Priority settings in the BIOS Setup. The system can not be shut down. It is best to shut down your computer using the Shut Down icon in the operating system. [. . . ]