User manual MSI MS-7549

[. . . ] Ths equpment generates, uses and can radate rado frequency energy and, f not nstalled and used n accordance wth the nstructons, may cause harmful nterference to rado communcatons. However, there s no guarantee that nterference wll not occur n a partcular nstallaton. If ths equpment does cause harmful nterference to rado or televson recepton, whch can be determned by turnng the equpment off and on, the user s encouraged to try to correct the nterference by one or more of the measures lsted below. Notce 1 The changes or modficatons not expressly approved by the party responsble for complance could vod the user's authorty to operate the equpment. [. . . ] ⷠIn Dual-Channel mode, make sure that you nstall memory modules of the same type and densty n dfferent channel DIMM slots. ⷠTo enable successful system boot-up, always nsert the memory modules nto the DIMM1 first. The memory module has only one notch on the center and wll only fit n the rght orentaton. Then push t n untl the golden finger on the memory module s deeply nserted n the DIMM slot. The plastc clp at each sde of the DIMM slot wll automatcally close when the memory module s properly seated. Manually check f the memory module has been locked n place by the DIMM slot clps at the sdes. You can barely see the golden finger f the memory module s properly nserted n the DIMM slot. To connect the ATX 24-pn power supply, make sure the plug of the power supply s nserted n the proper orentaton and the pns are algned. If you'd lke to use the 20-pn ATX power supply, please plug your power supply along wth pn 1 & pn 13 (refer to the mage at the rght hand). Make sure that all the connectors are connected to proper ATX power supples to ensure stable operaton of the manboard. To connect an LCD montor, smply plug your montor cable nto the DVI connector, and make sure that the other end of the cable s properly connected to your montor (refer to your montor manual for more nformaton. It s easy to dfferentate between audo effects accordng to the color of audo jacks. Lne-In (Blue) - Lne In, s used for external CD player, tape-player or other audo devces. If you nstall two IDE devces on the same cable, you must configure the drves separately to master / slave mode by settng jumpers. When connectng the wre to the connectors, always note that the red wre s the postve and should be connected to the +12V; the black wre s Ground and should be connected to GND. If the manboard has a System Hardware Montor chpset on-board, you must use a specally desgned fan wth speed sensor to take advantage of the CPU fan control. You can nstall Dual Core Center utlty that wll automatcally control the CPU fan speed accordng to the actual CPU temperature. ⷠFan cooler set wth 3 or 4 pns power connector are both avalable for CPUFAN1. To clear the warnng, you must enter the BIOS utlty and clear the record. Ths connector allows you to connect the front panel audo and s complant wth Intel® Front Panel I/O Connectvty Desgn Gude. There s a CMOS RAM onboard that has a power supply from an external battery to keep the data of system configuraton. Wth the CMOS RAM, the system can automatcally boot OS every tme t s turned on. [. . . ] Cell Menu Use ths menu to specfy your settngs for frequency/voltage control and overclockng. m-Flash Use ths menu to read/ flash the BIOS from storage drve (FAT/ FAT32 format only). Load Fal-Safe Defaults Use ths menu to load the default values set by the BIOS vendor for stable system performance. Load Optmzed Defaults Use ths menu to load the default values set by the manboard manufacturer specfically for optmal performance of the manboard. [. . . ]