User manual MSI MS-6367

[. . . ] Static electricity may damage the components. TOPICS Central Processing Unit: CPU Memory Power Supply Back Panel Connectors Jumpers Slots 2-1 Chapter 2 Central Processing Unit: CPU The mainboard supports AMD® Athlon and Duron processors. Make sure the CPU has a Heat Sink and a cooling fan attached on the top to prevent overheating. If you do not find the Heat Sink and cooling fan, contact your dealer to purchase and install them before turning on the computer. CPU Installation Procedures 1. As the CPU is likely to move while the lever is being closed, always close the lever with your finger pressing tightly on top of the CPU to make sure the CPU is properly & completely embedded into the socket. Press down the CPU Close Lever WARNING! Overheating will seriously damage the CPU and system, always make sure the cooling fan can work properly to protect the CPU from overheating. 2-2 Hardware Setup WARNING! Thermal Issue for CPU As processor technology pushes to faster speeds and higher performance, thermal management becomes increasingly crucial when building computer systems. [. . . ] PC1600 DDR SDRAM running at 100MHz will produce about 1. 6GB/s memory bandwidth. High memory bandwidth makes DDR an ideal solution for high performance PC, workstations and servers. 2-5 Chapter 2 DIMM Modules Combination At least one DIMM module should be installed on the motherboard. You can install memory modules in any combination as follows: Slot Momory Module Slot 1 64MB, 128MB, 256MB, (Bank 0 & 1) 512MB Slot 2 64MB, 128MB, 256MB, (Bank 2 & 3) 512MB Maximum System Memory Supported Total Memory 64MB~512MB 64MB~512MB 64MB~1GB Warning: We dont recommend to install DOUBLE-SIDED DDR266 module on DDR 3 slot because it will cause all memory modules to slower down and run at 200MHz. Installing DDR Modules 1. Then push it in until the golden finger on the memory module is deeply inserted in the socket. TIP: You can barely see the golden finger if the module is properly inserted in the socket. The plastic clip at each side of the DIMM slot will automatically close. Volt notch 2-6 Hardware Setup Power Supply The mainboard supports ATX power supply for the power system. Before inserting the power supply connector, always make sure that all components are installed properly to ensure that no damage will be caused. ATX 20-Pin Power Supply This connector allows you to connect to an ATX power supply. To connect to the ATX power supply, make sure the plug of the power supply is inserted in the proper orientation and the pins are aligned. Then push down the power supply firmly into the connector. 11 1 20 10 ATX Power Connector PIN 1 2 3 4 5 6 7 8 9 10 SIGNAL 3. 3V 3. 3V GND 5V GND 5V GND PW_OK 5V_SB 12V PIN 1 1 12 13 14 15 16 17 18 19 20 SIGNAL 3. 3V -12V GND PS_ON GND GND GND -5V 5V 5V 2-7 Chapter 2 Back Panel The Back Panel provides the following connectors: LAN (optional) Parallel Midi/Joystick Mouse Keyboard USB COM A VGA L-out L-in MIC Mouse Connector: JKBMS1 The mainboard provides a standard PS/2® mouse mini DIN connector for attaching a PS/2 ® mouse. The connector location and pin assignments are as follows: Pin Definition 6 4 2 1 5 3 PIN 1 2 3 4 5 6 SIGNAL Mouse DATA NC GND VCC Mouse Clock NC DESCRIPTION Mouse DATA No connection Ground +5V Mouse clock No connection PS/2 Mouse (6-pin Female) 2-8 Hardware Setup Keyboard Connector: JKBMS1 The mainboard provides a standard PS/2® keyboard mini DIN connector for attaching a PS/2® keyboard. You can plug a PS/2® keyboard directly into this connector. Pin Definition 6 4 2 1 5 3 PIN 1 2 3 4 5 6 SIGNAL Keyboard DATA NC GND VCC Keyboard Clock NC DESCRIPTION Keyboard DATA No connection Ground +5V Keyboard clock No connection PS/2 Keyboard (6-pin Female) USB Connectors The mainboard provides an OHCI (Open Host Controller Interface) Universal Serial Bus root for attaching USB devices such as keyboard, mouse or other USB-compatible devices. You can plug the USB device directly into the connector. USB Port Description 1234 PIN 1 2 3 4 5 6 7 8 SIGNAL VCC -Data 0 +Data0 GND VCC -Data 1 +Data 1 GND DESCRIPTION +5V Negative Data Channel 0 Positive Data Channel 0 Ground +5V Negative Data Channel 1 Positive Data Channel 1 Ground 5678 USB Ports 2-9 Chapter 2 Serial Port Connector: COM A The mainboard offers one 9-pin male DIN connector as serial port COM A. The port is a 16550A high speed communication port that sends/receives 16 bytes FIFOs. 1/8 Stereo Audio Connectors Line Out Line In MIC 2-12 Hardware Setup Connectors The mainboard provides connectors to connect to FDD, IDE HDD, case, USB Ports, IR module and CPU/System FAN. Floppy Disk Drive Connector: FDD1 The mainboard provides a standard floppy disk drive connector that supports 360K, 720K, 1. 2M, 1. 44M and 2. 88M floppy disk types. 2 1 34 33 FDD1 2-13 Chapter 2 The mainboard uses an IDE controller on the nVIDIA® MCP-D chipset that provides PIO mode 0-4, Bus Master, and Ultra DMA 33/66/100 modes. You can connect up to four hard disk drives, CD-ROM or 120MB Floppy to IDE1 and IDE2. IDE1 (Primary IDE Connector) - The first hard disk drive should always be connected to IDE1. IDE2 (Secondary IDE Connector) - You can connect a Master and a Slave drive to IDE2. Hard Disk Connectors: IDE1 & IDE2 40 39 40 39 2 12 1 IDE2 IDE1 TIP If you install two hard disks on cable, you must configure the second drive to Slave mode by setting its jumper. Refer to the hard disk documentation supplied by hard disk vendors for jumper setting instructions. 2-14 Hardware Setup Case Connector: JFP1 The case connector block JFP1 allows you to connect to the Power Switch, Reset Switch, Keylock, Speaker, Power LED, and HDD LED on the case. Reset Switch Speaker Buzzer (short pin) + Power Switch Power LED HDD LED + Keylock JFP1 Power Switch Connect to a 2-pin push button switch. Reset Switch Reset switch is used to reboot the system rather than turning the power ON/ OFF. If on-board Buzzer is available, then: 2-15 Chapter 2 Short pin 14-15: Open pin 14-15: On-board Buzzer Enabled. On-board Buzzer Disabled HDDLED HDD LED shows the activity of a hard disk drive. Keylock Keylock allows you to disable the keyboard for security purpose. [. . . ] Follow the instructions below to clear the data: 1 JBAT1 3 3 1 1 Clear Data Keep Data WARNING! You can clear CMOS by shorting 2-3 pin while the system is off. Avoid clearing the CMOS while the system is on; it will damage the mainboard. 2-22 Hardware Setup Slots slots. The motherboard provides one AGP slot and three 32-bit Master PCI AGP Slot PCI Slots AGP (Accelerated Graphics Port) Slot The AGP slot allows you to insert the AGP 1. 5V graphics card. AGP is an interface specification designed for the throughput demands of 3D graphics. [. . . ]