User manual MORPHY RICHARDS ULTRALIGHT BAGLESS VACUUM CLEANER REV 2

[. . . ] Use only genuine Morphy Richards spare parts and accessories Never over-extend the hose such that the cleaner is pulled over. If the cleaner is knocked over, switch off before attempting to upright. Never pick the cleaner up by the floor nozzle when connected to the mains, use the carrying handle. away from the floor nozzle whenever the cleaner is connected to the mains. [. . . ] 5 Step on the handle release pedal to release the handle to the desired position. IMPORTANT: To prevent damage to carpets, never leave the cleaner switched on in one place for an extended period. · Never have the brushes set too low such that the cleaner is hard to push. Floor nozzle height adjustment C Before using the cleaner the floor nozzle height must be set to the correct height. Note: The height adjustment only comes into effect when the handle is released by the handle release pedal È. B Using attachments Follow steps 1-4 (using on carpets) but set the carpet height adjustment knob to deep carpet setting. Insert the hose clip ~ into the hose clip slot Ë. C DEEP CARPET TOOLS HARD FLOOR D min max MEDIUM CARPET 4 73322 Rev 2 17/1/05 2:42 PM Page 5 Push the required attachment firmly onto the end of the hose. · If additional length is required, attach one or both extension tubes. · IMPORTANT: Always fix the hose clip ~ to the main body slot Ë when using the hose and tools. · Never over extend the hose such that the cleaner is pulled over. IMPORTANT: Turning the cleaner sideways helps prevent the cleaner being pulled along by the stretch hose. · Emptying Empty the dust canister regularly even if it does not look full this will maintain the performance. E 2 Lift-up the dust canister release and pull the canister away from the main body. 4 Turn the lid 1/4 turn anti-clockwise to unlock, lift off the lid with pleated filter Ì, put to one side. F 5 Lift out the central mesh filter Ô from the dust canister G. 9 Re-fit pleated filter with lid into the dust canister and turn lid 1/4 turn clockwise to lock. Then re-fit front cover. Using & cleaning turbo nozzle Attach the turbo nozzle to the hose end for use on upholstery and stairs. If they are tightly wound around the brush carefully snip the fibres with scissors, being careful not to damage the brush bar, pull away from the brush bar and dispose. F Ì Ï Ô Safety cut-out If the cleaner overheats a motor protection thermostat will automatically switch the motor off. If this happens, switch the cleaner off, unplug from the power supply and leave the cleaner to cool for at least 30 minutes. Check the airways for blockages, empty dust canister and clean the filters before restarting. Ó Î ¤ E < 5 73322 Rev 2 17/1/05 2:42 PM Page 6 Cleaning the filters To maintain suction the pleated filter must be shaken clean each time the dust canister is emptied. Failure to clean the filter will reduce suction and could damage the motor if used for a prolonged period. If the filters become damaged they must be replaced. Motor protection filter I The motor protection filter Ò is located underneath the dust canister 1 Remove the dust canister. The filter may also be washed in water (no detergents) but must be totally dry before re-fitting. [. . . ] 12 Place one end of the new belt over the motor shaft and the other around the pulley end of the brush. 13 Locate the left hand side of the brush bar first, then while pulling the right hand side of the nozzle gently outwards and stretching the belt, lower the right hand side of the brush into its location. 14 Rotate the brush by hand to ensure it is correctly and securely located. 16 Replace the top cover, hooking it in at the front first and by pressing the handle release pedal to allow the rear to correctly locate N. 17 Turn the cleaner face down and re-fit and tighten the four fixing screws, do not overtighten. [. . . ]