User manual MORPHY RICHARDS TURBO STEAM IRON 40684

[. . . ] To avoid the risk of electric shock, do not disassemble the iron, but telephone Morphy Richards for advice. Incorrect reassembly can cause a risk of electric shock when the iron is used. Special instructions · If your iron does not work, check the following points: Has the temperature control been set to the required temperature?· WARNING: When not in use, your iron should never be placed flat and left on an ironing board. To prevent damage to the textile being ironed, follow the temperature guide carefully (test the inside of the hem of the garment). [. . . ] In hard water areas, the use of distilled or demineralised water is recommended. Never use battery topping up fluid or water containing any substances like starch, or sugar, or defrosted water from a refrigerator. Warning: When filling your iron with tap water, always use the beaker provided. Never fill directly under the tap. FEATURES OF YOUR A IRON Temperature indicator light The indicator light under the control knob shows that the iron is warming up. When the required temperature is reached, the light will go out and will cycle on-off during operation. 2 Dry ironing You can use your iron as a dry iron only. Make sure the variable steam control < is set to the `0' symbol. The spray feature may be used provided there is water in the tank (see `Filling' section). You do not need to put any water in the tank when dry ironing only. B Temperature control B Plug in the iron and switch on. The `power on' indicator lights , , , situated in the back cover, will illuminate. Set the temperature control dial B to the temperature required, but don't start ironing immediately. If you wait a few minutes, the iron will stabilise at the required setting. Your Morphy Richards iron is fitted with an indicator light which will go on and off while you are ironing. This is perfectly normal as it shows that the iron is maintaining the heat setting you have chosen. It is always a good idea to begin with cool fabrics and work up to higher settings. An iron heats up quicker than it cools down so you'll save time and electricity. Spray C Press the spray button ¤ and aim the spray of water at stubborn creases. You can do this whilst dry ironing, providing there is water in the tank. When using the water spray, it may be necessary to push the button a few times to get the spray pump primed. C Variable steam D Fill the iron with water as described in `Filling', and insert the plug into the electrical socket. The steam output can be varied from low to high by sliding the variable steam control D. D lower steam 2 dot higher steam 3 dot When using the iron at the bottom of the steam range, the slider switch should be adjusted to the `lowest setting'. The steam facility should only be used on garments which are suitable for ironing at 2 and 3 dot settings. 5 40684 rev3 17/6/08 17:03 Page 6 E Shot of steam E Press the shot of steam button / to obtain a burst of extra steam for ironing out creases in heavy material such as denim etc. The shot of steam can be used whilst dry ironing, providing there is water in the tank, and the temperature control is set within the steam range. Do not use shot of steam at temperatures below the steam range shown on the control. Note: For optimum steam quality, do not operate the shot more than three times in succession. Auto shut-off (certain models only) If your iron is fitted with the auto shut-off function, it will automatically shut down after a set period. If the iron is left unattended in the horizontal position, it will shut down after 1 minute. [. . . ] This guarantee is offered as an additional benefit and does not affect your statutory rights as a consumer. This guarantee is valid in the UK and Ireland only. 5 6 7 · EXCLUSIONS Morphy Richards shall not be liable to replace or repair the goods under the terms of the guarantee where: 1 The fault has been caused or is attributable to accidental use, misuse, negligent use or used contrary to the manufacturer's recommendations, or where the fault has been caused by power surges or damage caused in transit. The appliance has been used on a voltage supply other than that stamped on the products. Repairs have been attempted by persons other than our service staff (or authorised dealer). [. . . ]