User manual MORPHY RICHARDS STORM CYCLONIC

[. . . ] Children should be supervised to ensure that they do not play with the appliance. · · · · ELECTRICAL REQUIREMENTS Check that the voltage on the rating plate of your appliance corresponds with your house electricity supply which must be A. C. If the socket outlets in your home are not suitable for the plug supplied with this appliance the plug should be removed and the appropriate one fitted. If you cut off the plug and let go of the cable it will rewind into the machine therefore you must pull out a length of cable and secure it before cutting the plug off and re-fitting a new one. WARNING: The plug removed from the mains lead, if severed, must be destroyed as a plug with a bared flexible cord is hazardous if engaged into a live socket outlet. [. . . ] A cover on the bottom of the large turbo nozzle allows access to the turbine fan. Combination floor nozzle The combination floor nozzle can be adjusted to suit different floor surfaces. The brushes should be down for use on hardfloors or damage may occur. Hardfloor nozzle (certain models only) Attach the hardfloor nozzle to the extension tubes. This nozzle is ideal for use on wood, laminate, tile and vinyl flooring. Hand tools The crevice tool Ú (for awkward places, behind radiators etc) and the upholstery nozzle with clip on brush Ò (for curtains and upholstery) are stored in the tool drawer ·. The crevice tool is used for hard surfaces, pelmet, delicate objects etc B. 4 UK Helpline 0870 060 2604 Replacement Parts 0870 167 6635 Ireland Helpline 1800 409119 71064 Rev1 18/5/07 10:55 am Page 5 Quick guide to accessories: Combination Large turbo floor nozzle nozzle only) Small turbo nozzle only) Hard floor nozzle only) Crevice tool Upholstery nozzle with clip on-brush (certain models (certain models (certain models Carpet 3 With brushes retracted 3 Rugs 3 With brushes retracted 3 Wood/ laminate Tile 3 With brushes down 3 3 With brushes down 3 Vinyl Upholstery Stairs Small spaces 3 3 3 3 3 3 3 3 CONTROLS Power 1 Assemble the nozzle, extension tube and hose as shown. (Shown on page 3) Pull out the mains cable to it's full length and plug into the mains supply. Suction can also be controlled using the airflow regulator on the hose handle. Closed for maximum suction, open for reduced suction. 2 3 Automatic cable rewind After use, unplug and press the cable rewind switch to retract the cable. WARNING: When using the cable rewind, always hold the plug as the cable will rewind quickly. Variable power A Variable power switch fl varies the suction power as required. For example, maximum suction can be used for cleaning carpets, hard floors 5 71064 Rev1 18/5/07 10:55 am Page 6 DUST CANISTER Emptying To obtain the best results from your cleaner empty the dust canister regularly, otherwise the airflow and cleaning power will be reduced. 1 Everytime the dust canister is emptied, turn the yellow dial (a minimum of 5 revolutions) prior to pressing the dust canister release button (this will agitate the fine dust between the filter pleats and restore the air flow) Remove the dust canister from the product by pressing the dust canister release button < Lift up the lid and remove the canister from the product, pulling the dust canister away from the product. C Holding the dust canister over a dustbin press the dust release button as shown D, the bottom of the dust container will drop down to release the dirt. Close the bottom of the dust canister by pressing the base upwards until it clicks into place. 1 FILTERS Cleaning canister filter Access the filter assembly by removing the lid. Use the filter cleaning brush to remove any fluff from the outside of the mesh filter. Both the mesh and pleated filters may be washed (in cool water only) but must be thoroughly air dried before refitting. · To re-assemble, locate the pleated filter into the lid then secure into place with the mesh filter by rotating the mesh filter clockwise. Fit the lid with filter assembly onto the canister then rotate clockwise until it locks into place. E OPEN C 2 3 4 2 5 D 3 4 · 5 6 Exhaust filter The exhaust filter  is located at the rear of the cleaner. Pull the bottom of the filter outwards so the top of the filter unhooks F from the filter recess. Foam filters may be washed (in cool water), thoroughly air-dried and re-fitted. The pleated filters used on the Allergy models cannot be washed and should be replaced every 6 months or sooner depending on use. ALLERGY SUFFERERS If the allergy sufferer is emptying the product it is recommended that the container is placed into a plastic bag to empty. 1 Place the container inside the plastic bag, releasing the container with one hand whilst holding the top of the bag closed with the other, leave the dust to settle for a few seconds before carefully removing the empty canister. [. . . ] Morphy Richards are not liable to carry out any type of servicing work, under the guarantee. This guarantee does not confer any rights other than those expressly set out above and does not cover any claims for consequential loss or damage. This guarantee is offered as an additional benefit and does not affect your statutory rights as a consumer. This guarantee is valid in the UK and Ireland only. 4 · 5 · 6 · · Exclusions Morphy Richards shall not be liable to replace or repair the goods under the terms of the guarantee where: 1 The fault has been caused or is attributable to accidental use, misuse, negligent use or used contrary to the manufacturers recommendations or where the fault has been caused by power surges or damage caused in transit. [. . . ]