User manual MORPHY RICHARDS STEAM GENERATORS

[. . . ] · If the supply cord is damaged, it must be replaced by the manufacturer, it's service agent or similarly qualified persons in order to avoid a hazard. Other safety considerations · Use the steam generator only for it's intended use. · To protect against the risk of electric shock, do not put the appliance in water or in any other liquid. · Always disconnect the steam generator from the electrical supply and the tank from the base unit when filling with water and emptying. · Always disconnect the steam generator from the electrical supply when cleaning or when not in use. [. . . ] If they don't, you should follow the fabric guide on page 3, but be sure to test the temperature by ironing the hem of the garment or similar area first. If you turn the control dial down from a hot setting to a cooler setting, wait until the iron temperature has stabilised before you continue ironing. , , , O I Iron unit / Steam button ¤ Temperature control dial < Sole plate > Temperature indicator light fi Supply cord from base unit Base unit fl Anti-scale cartridge Water tank · Power cord , Power switch with indicator light , , Boiler temperature indicator light Steam Facility (certain models only) Spray unit  Spray bottle (20ml) Filling 1 Place the steam generator on a stable ironing board or table, with the iron resting on it's stand. A 3 Remove the anti-scale cartridge by pulling upwards B. B  4 42271 rev4 30/7/08 15:56 Page 5 4 Fill the tank up to the `fill to here' line with clean tap water C. Never use battery C topping up fluid or water containing any substances like starch or sugar, or defrosted water from a refrigerator. 5 Re-install the anti-scale cartridge and replace the water tank on the base unit D. D 6 Always pour out remaining water after use. also illuminate, indicating the boiler is on it's heating cycle and will extinguish when the required temperature is reached. 5 Turn the temperature dial on the iron in a clockwise direction, select dot-1, dot-2 or dot-3 according to the recommendation of the garment label. 6 The iron's temperature indicator light > goes off when the required temperature is reached. 7 Depress the steam button / for one minute to clean the steam generating system (for first time use). 10 To switch the unit off, turn the power switch on the base unit to `O' (OFF). Re-filling 1 When the water level reaches a low level, the pump begins to emit a loud noise. 2 Slide out the water tank and fill (see `Filling' instructions). Dry ironing 1 Connect the appliance to a suitable mains outlet. 2 Turn the temperature dial on the iron in a clockwise direction, select dot-1, dot-2 or dot-3 according to the recommendation of the garment label. 3 The temperature indicator light glows on the iron, indicating that it is switched on. 4 When the required temperature is reached, the temperature indicator light on the iron goes off. It is always a good idea to begin with 'cool' fabrics and work up to higher settings. An iron heats up quicker than it cools down, so you'll save time and electricity. Steam ironing 1 Unwind and straighten the power cord · and supply cord fi. 2 Slide out the water tank and fill (see `Filling' instructions). Turn the power switch , on the base unit to `I' (on) and the indicator will glow. 4 The boiler ready indicator light , , situated above the `power switch' , will Steam ironing The spray unit (certain models only) The spray unit can be used at any time and does not affect any product settings. 5 42271 rev4 30/7/08 15:56 Page 6 Filling the spray unit The spray feature is lightly secured to the handle. To fill the water tank, pull the spray unit forward using the two moulded lugs provided. Remove the spray bottle  from the base of the pump and fill with water to the `MAX' mark. Re-fit the spray bottle, making sure the arrows (printed black) are in line. Replacement anti-scale refills To obtain replacement anti-scale refills, telephone our spares number on: 0844 873 0719. [. . . ] In the unlikely event of any appliance proving to be faulty within 28 days of purchase, it should be returned to the place of purchase for it to be replaced. If the fault develops after 28 days and within 24 months of original purchase, you should contact the Helpline number quoting Model number and Serial number on the product, or write to Morphy Richards at the address shown. Subject to the exclusions set out below (see Exclusions), the faulty appliance will then be repaired or replaced and dispatched usually within 7 working days of receipt. If, for any reason, this item is replaced during the 2 year guarantee period, the guarantee on the new item will be calculated from the original purchase date. [. . . ]