User manual MORPHY RICHARDS STEAM GENERATOR

[. . . ] This guarantee does not confer any rights other than those expressly set out above and does not cover any claims for consequential loss or damage. This guarantee is offered as an additional benefit and does not affect your statutory rights as a consumer. All Morphy Richards products are individually tested before leaving the factory. In the unlikely event of any appliance proving to be faulty within 28 days of purchase it should be returned to the place of purchase for it to be replaced. If the fault develops after 28 days and within 24 months of original purchase, you should contact the Helpline number quoting Model number and Serial number on the product, or write to the address below. [. . . ] If your iron is placed for a few moments on the iron rest plate, this plate may reach very high temperatures. In this instance, do not touch the iron soleplate or the iron rest plate until the iron and the iron rest have cooled down. Special instructions 1 If your steam generator does not work, check the following points: Has the temperature control been set to the required temperature?2 Warning: When in use, your iron should never be placed flat and left on an ironing board. 3 To prevent damage to the fabric being ironed, follow the temperature guide carefully. 4 If you drop or severely knock your steam generator this could cause internal damage even if the outside appears alright. 5 The temperature of accessible surfaces may be high when the appliance is operating. SAVE THESE INSTRUCTIONS 2 Electrical requirements Check that the voltage on the rating plate of your appliance corresponds with your house electricity supply, which must be A. C. If the socket outlets in your home are not suitable for the plug supplied with this appliance the plug should be removed and the appropriate one fitted. IMP0RTANT : THE PLUG REMOVED FROM THE MAINS LEAD, IF SEVERED, MUST BE DESTROYED AS A PLUG WITH A BARED FLEXIBLE CORD IS HAZARDOUS IF ENGAGED INTO A LIVE SOCKET OUTLET. Should the fuse in the 13 amp plug require replacement, a 13 amp BS1362 fuse must be fitted. WARNING : THIS APPLIANCE MUST BE EARTHED. Instructions for use Temperature guide Heat setting markings on the adjustable control dial of all Morphy Richards irons match those of the international Textile Care Labelling Code. Symbol (120 C Max) Cool Control knob positions Fabric o (160 C Max) Warm o (210 C Max) Hot o Do not iron at all Nylon, Acetates e. g. If moisture required use damp cloth (Not Acetate) Wool, polyester mixtures e. g. Rayon/Linen Fabrics requiring this setting usually require steam pressing for heavy cotton, denim etc Ironing Steaming 3 Components of your iron Location Locate the steam generator horizontally on the iron rest plate of your ironing board (if large enough) or on a heat resistant stand at the same height of your ironing board or below it. Always ensure the generator is on a firm surface when ironing. Before use Remove any protective films or sticker from the soleplate and the cabinet, if any. When ironing with the steam facility at the 1 dot setting, the steam output should be set at the lower end of the steam range. If they don't you should follow the fabric guide on page 3, but be sure to test the temperature by ironing the hem of the garment or similar area first. If you turn the control dial down from a hot setting to a cooler setting, wait until the iron temperature has stabilised before you continue ironing. power stand by antiscale replace Filling 1 Place the steam generator on a stable ironing board or table, with the iron resting on its stand. 2 Remove the detachable water tank by sliding outwards. Iron unit Steam button Temperature control dial Sole plate Temperature indicator light Supply cord from base unit FILL TO HERE Base unit Anti-scale cartridge Water tank Power cord Power switch -Standby mode indicator (red) -Power indicator (green) -Sleep mode indicator (green and red flashing alternate) Replace anti-scale cartridge indicator Steam level indicators 3 Remove the anti-scale cartridge by pulling upwards. 4 4 Fill the tank upto the `fill to here' line with clean tap water. Never use battery topping-up fluid or water containing any substances like starch or sugar, or defrosted water from a refrigerator. 5 Re install the anti-scale cartridge and replace the water tank on the base unit. FILL TO HERE FILL TO HERE 6 Always pour out the remaining water after use. 5 The iron's temperature indicator light goes off when the required temperature is reached. 6 Depress the steam button for 1 minute to clean the steam generating system (for first time use). Note: If you press the steam button before the steam generator reaches its required temperature a warning double bleep will sound. 8 Press the power switch to choose the steam level from `steam off', `low steam', `medium steam' and `maximum steam'. 11 To switch the unit off turn the temperature dial on the iron in an anticlockwise direction to `Min'. [. . . ] Using your anti-scale and alert system This appliance has an electronic system that monitors the water hardness. Filling/Refilling your anti-scale cartridge 1 When the anti-scale cartridge indicator is flashing you will need to replace the cartridge. (Towards the end of the useful life of the cartridge, the warning light will flash briefly every time the tank is refilled, however, when the cartridge needs replacing the light will flash for a longer time, ie. 1 minute or more). 2 If a new cartridge is not available you may continue operating the appliance but scale will build up in the system. [. . . ]