User manual MORPHY RICHARDS RN40310MUK REV 3

[. . . ] The iron must not be left unattended while it is connected to the supply mains. When placing the iron on its heel, ensure that the surface on which the heel is placed is stable. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience or knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. · · · Other safety considerations Use the iron only for its intended use. [. . . ] If you turn the control dial down from a hot setting to a cooler setting, wait until the iron temperature has stabilised before you continue ironing. 4 UK Helpline 0844 871 0953 Replacement Parts 0844 873 0719 Ireland Helpline 1800 409 119 RN40310MUK Rev3:RN40310MUK Rev3 20/11/2009 16:01 Page 5 FILLING A 1 Make sure that the iron is not plugged in and then set the steam control / to the ` ' position before filling the iron with water. Lift up the fill cap and fill with water through the filling hole > using the beaker provided A. IN HARD WATER AREAS, THE USE OF DISTILLED OR DEMINERALISED WATER IS RECOMMENDED. Never use battery topping up fluid or water containing any substances like starch or sugar, or defrosted water from a refrigerator. WARNING: When filling your iron with tap water, always use the beaker provided. Never fill directly under the tap. FEATURES OF YOUR IRON Temperature indicator light The indicator light shows that the iron is warming up. When the required temperature is reached, the light will go out and will cycle on-off during operation. A 2 Dry ironing You can use your iron as a dry iron only. The spray feature may be used provided there is water in the tank (see filling section). You do not need to put any water in the tank when dry ironing only. B Spray C Press the spray button ¤ and aim the spray of water at stubborn creases. You can do this whilst dry ironing providing there is water in the tank. When using the water spray, it may be necessary to push the button a few times to get the spray pump primed. TEMPERATURE CONTROL Plug in the iron and switch on. Set the temperature control dial to the temperature required B, but don't start ironing immediately. If you wait a few minutes, the iron will stabilise at the required setting. Your Morphy Richards iron is fitted with an indicator light , which will go on and off while you are ironing. This is perfectly normal as it shows that the iron is maintaining the heat setting you have chosen. It is always a good idea to begin with cool fabrics and work up to higher settings. An iron heats up quicker than it cools down, so you'll save time and electricity. C Variable steam Fill the iron with water as described in `Filling', then insert the plug into the electrical socket. The steam output can be switched from off to on by sliding the steam control / D. The steam facility should only be used on garments which are suitable for ironing at the 3 dot setting. D Steam No steam For details of other Morphy Replacement Parts 0870 our website: UK Helpline 0870 060 2614Richards products, please see157 6645 Ireland Helpline 1800 409119 5 RN40310MUK Rev3:RN40310MUK Rev3 20/11/2009 16:01 Page 6 E Shot of steam E (certain models only) Press the shot of steam button < to obtain a burst of extra steam for ironing out creases in heavy material, such as denim etc. The shot of steam can be used whilst dry ironing, providing there is water in the tank, and the temperature control is set within the steam range. Do not use shot of steam at temperatures below the steam range shown on the control. Note: For optimum steam quality, do not operate the shot more than three times in succession. MAINTENANCE Emptying and storing When you have finished ironing, unplug your iron. [. . . ] Please refer to the one year guarantee for more information. YOUR ONE YEAR GUARANTEE It is important to retain the retailer's receipt as proof of purchase. Please quote the following information if the product develops a fault. All Morphy Richards products are individually tested before leaving the factory. In the unlikely event of any appliance proving to be faulty within 28 days of purchase, it should be returned to the place of purchase for it to be replaced. EXCLUSIONS Morphy Richards shall not be liable to replace or repair the goods under the terms of the guarantee where: 1 The fault has been caused or is attributable to accidental use, misuse, negligent use or used contrary to the manufacturer's recommendations or where the fault has been caused by power surges or damage caused in transit. [. . . ]