User manual MORPHY RICHARDS ORB PETS CYCLONE VACUUM CLEANER REV 1

[. . . ] · Do not store the appliance near hot ovens or heating appliances. Mains lead · Do not allow the mains lead to become strained or run this appliance over it. · If the electrical cable becomes damaged the complete cable assembly must be replaced. Do not attempt this task yourself, contact Morphy Richards using the replacement parts number on the front of this leaflet. Electrical requirements Check that the voltage on the rating plate corresponds with your house electricity supply which must be A. C. If the socket outlets in your home are not suitable for the plug supplied with this appliance the plug should be removed and the appropriate one fitted. [. . . ] C Using the turbo nozzle Attach the turbo nozzle to the hose end for use on upholstery and stairs. Cleaning the turbo nozzle The turbo nozzle should be regularly cleaned and any hairs or fibres wrapped around the brush bar removed to maintain optimum performance. To aid cleaning, the turbo nozzle can be opened up by pushing the button on the nozzle forwards. È C Í Both these tools are stored beneath the lid. 4 orb cyclone 73171M REV 1 30/7/04 11:36 AM Page 5 Dust disposal To obtain the best results from your cleaner empty the dust container regularly, otherwise the airflow and cleaning power will be reduced. D 4 Close the bottom of the dust container by pressing the base upwards until it clicks into place. 5 Re-insert the dust container into the product and close the lid to re-fit. G G D Cleaning the dust compartment filter 2 Lift the container away from the product. E It is essential that filters are cleaned regularly to maintain performance. 1 Remove the dust container from the product as detailed in the previous section. H. E H 3 Holding the dust container over a dustbin, lift up the flap on top of the handle and press the dust container release button as shown F the bottom of the dust container will drop down to release the dirt. F 5 orb cyclone 73171M REV 1 30/7/04 11:36 AM Page 6 3 Remove the top mesh filter as shown I. The pleated filter can be gently knocked against the side of the dustbin to remove excess dust. Cleaning the exhaust filter I The exhaust filter is located at the back of the product. To remove, press the clip and pull the filter cover away from the product. K Remove the filter. To refit the filter, reassemble and locate into the hole in the top of the dust container. · The filter should be regularly washed in cold water and left to air dry before inserting back into the machine. IMPORTANT: The dust container will not lock back onto the machine unless the filter is fitted correctly. K The exhaust filter is non-washable. To remove fine dust use the crevice tool brush to gently clean between the pleats. It is recommended that the exhaust filter is replaced every 6 months or sooner if it becomes damaged. IMPORTANT · All filters should be checked regularly for signs of damage, preferably after each cleaning task. · Always disconnect the cleaner from the mains when checking filters. Failure to do so may result in damage to your product. Pre-motor filter An additional pre-motor filter is located underneath the dust compartment lid. Remove and shake rigorously to clean. J 6 orb cyclone 73171M REV 1 30/7/04 11:36 AM Page 7 Storage position When finished you can store the tubes and accessories by locating the tube storage clip into the slot on the bottom of the cleaner as shown. L Helpline If you have any difficulty with your appliance do not hesitate to call us. We are likely to be more help than the store from where it was bought. Please have the following information ready to enable our staff to help you. [. . . ] For example, the filters must be cleaned regularly and replaced if necessary. EXCLUSIONS Morphy richards shall not be liable to replace or repair the goods under the terms of the guarantee where: 1 The fault has been caused or is attributable to accidental use, misuse, negligent use or used contrary to the manufacturers recommendations or where the fault has been caused by power surges or damage caused in transit. 2 The appliance has been used on a voltage supply other than that stamped on the products. 3 Repairs have been attempted by persons other than our service staff (or authorised dealer). [. . . ]