User manual MORPHY RICHARDS INTELLIDOME

[. . . ] RN42236MUK Rev2_Instruction Book 25/10/2010 11:38 Page 1 Upon registration with Morphy Richards (UK & ROI only) Register online for your 2 year guarantee. (UK and Ireland customers only) www. morphyrichards. co. uk TM Ironing system (pressurised) Please read and keep these instructions Getting the best from your new ironing system. . . . Safety first Caution must be used when handling this appliance as it does get very hot. Always switch off the unit and allow to cool before cleaning or storing. Water tank The fixed water tank can be re-filled at any time during ironing. Performance To extend the performance and life of your IntelliDome generator, ensure that you replace the anti-scale filter according to the on-board indicator. Regularly remove any calcium build-up which may have accumulated in the boiler (see cleaning instructions). ! To improve the life of your new product and to ensure the cleanliness of your clothes, we strongly recommend the use of distilled or demineralised water. RN42236 MUK Rev 2 For competitions, product hints and tips and much more, join us online at our blog, Facebook or Twitter pages. www. homeofthehouseproud. com www. facebook. com/LoveYourHome www. twitter. com/LoveYourIroning If you have a problem or complaint, please call our dedicated UK based helpline before returning your product to the retailer from where it was purchased. [. . . ] The unit will heat and automatically default to the LOW STEAM level, the STEAM ICON will flash on the display screen and will remain permanently on when steam is available for ironing. The AUTO STANDBY feature will activate if the iron is not used for 15 minutes. Press the POWER STANDBY button or steam trigger to reactivate the iron. I MEDIUM STEAM LEVEL J HIGH STEAM LEVEL The STEAM ICON will flash until the unit reaches the selected temperature. Once the temperature has been reached, the STEAM ICON will remain lit. When navigating though the steam settings, a SHORT BEEP will be heard for every operation of the STEAM SETTING +/- buttons a further LONGER BEEP will be heard once the unit has reached the selected setting. Note: During ironing, the pump will operate periodically to `top up' the boiler with water. This is quite normal and lasts for a few seconds only. VERTICAL STEAM Hold the iron in a vertical position between 1cm and 2cm away from the item K. This feature is especially useful for removing creases from hanging clothes, curtains, wall hangings etc. Steam settings To increase or decrease the steam setting, press the STEAM SETTING +/- buttons. These settings include: NO STEAM G, LOW STEAM LEVEL H, MEDIUM STEAM LEVEL I and HIGH STEAM LEVEL J. K G STEAM FUNCTION NO STEAM During the steaming process, small amounts of water may be ejected from the soleplate. This is normal and can be avoided by using the steam for short amounts of time and only when the iron is at the correct temperature (the indicator light on the iron goes out when ready). Sudden jolts of the boiler unit can also cause water droplets on the soleplate; therefore, do not move the base unit during ironing. We recommend for the first time ironing that you iron over an old towel. 11 11 H LOW STEAM LEVEL For details of other Morphy Richards products, please see our website: RN42236MUK Rev2_Instruction Book 25/10/2010 11:38 Page 12 3. DRY IRONING Always make sure there is water in the tank otherwise the LOW WATER indicator will activate. 1 Always make sure the water tank is quarter full, otherwise the LOW WATER INDICATOR ICON will activate. The LCD display screen will illuminate for 1 second accompanied by a short beep sound, the unit will then turn off and will remain in STANDBY mode until re-activated. Press the POWER STANDBY button to activate the unit and set the iron temperature dial to the dot setting required. Press the STEAM +/­ buttons until the NO STEAM ICON is displayed on the LCD display screen L. WATER SPRAY (certain models only) Certain models are fitted with a water spray feature. Stubborn creases and excessively dry clothing can be softened by damping the material with water. This procedure means ironing can be achieved without applying excessive pressure. 2 3 Filling water spray tank M To fill the water spray tank with water, press the release button Ì and lift away the spray unit Î. Pull the tank Ó away from the spray unit in a downward direction, taking care not to damage the tank, and fill water to the `Full' mark. 4 M ÎÏ ÎÌ 5 L Ó NO STEAM 6 7 8 Turn the temperature dial on the iron to the dot setting required. The temperature indicator light on the iron will glow indicating the iron is heating. When the required temperature is reached, the temperature indicator light will go out and the iron is now ready to use. [. . . ] · · · Name of the product Model number as shown on the underside of the appliance. UK Helpline Replacement Parts Ireland Helpline 0844 871 0960 0844 873 0726 1800 409 119 To clean the exterior Allow the steam generator to cool and wipe over with a damp cloth and mild detergent, then wipe with a dry cloth. WEBSITE You may also contact us through our website, or visit the site to browse and purchase appliances, spare parts and accessories from the extensive Morphy Richards range. For details of other Morphy Richards products, please see our website: 15 RN42236MUK Rev2_Instruction Book 25/10/2010 11:38 Page 16 REGISTERING YOUR TWO YEAR GUARANTEE Your standard one year guarantee is extended for an additional 12 months when you register the product within 28 days of purchase with Morphy Richards. If you do not register the product with Morphy Richards within 28 days, your product is guaranteed for 1 year. To validate your 2 year guarantee register with us online at If the fault develops after 28 days and within 12 months of original purchase, you should contact the Helpline number quoting Model number and Serial number on the product, or write to Morphy Richards at the address shown. [. . . ]