User manual MORPHY RICHARDS IBCR1908

[. . . ] Illustration 2 Band Alarm Clock Radio Location of controls CR1908 OPERATING INSTRUCTIONS 1 2 3 4 5 6 7 8 Tuning control Time button Alarm button Sleep button Snooze button Hour button Minute button Speaker 9 10 11 12 13 14 15 FM wire aerial LED clock display Alarm on indicator PM indicator Band selector switch Function selector switch Volume control P. 2 Electrical requirements Check the voltage on the rating plate of your clock radio corresponds with your house electricity supply which must be A. C. If the socket outlets in your home are not suitable for the plug supplied with this appliance the plug should be removed and the appropriate one fitted. IMP0RTANT : THE PLUG REMOVED FROM THE MAINS LEAD, IF SEVERED, MUST BE DESTROYED AS A PLUG WITH A BARED FLEXIBLE CORD IS HAZARDOUS IF ENGAGED INTO A LIVE SOCKET OUTLET. [. . . ] The display will be extinguished to conserve battery life but the memory will retain details of the clock time and alarm settings. If the optional battery is not installed in case of the AC power failure the display will blink to indicate the power was interrupted. If the unit is not to be used for a prolonged period, remove the battery to avoid battery leakage. In the interests of environmental safety : dispose of batteries safely. P. 3 P. 4 Alarm operation 1 Press and hold the ALARM button (3) and simultaneously press the HOUR (6) or MINUTE button (7) to set the display to the desired alarm time. Set the FUNCTION SELECTOR switch (14) to the desired buzzer or radio `AUTO' alarm position. The ALARM ON indicator (11) will appear on the LED display (10). To stop the alarm tone The alarm is programmed to run for 1 hour 59 minutes. To switch the alarm setting off permanently, slide the FUNCTION SELECTOR switch (14) to the `Off' position. 2 2 3 Wake up to the radio alarm 1 Switch the FUNCTION SELECTOR switch (14) to the `ON' position to tune to the desired station. Set the BAND SELECTOR switch (13) to select either FM or MW wavebands as desired. The alarm will automatically turn off after a set period. Snooze function The alarm can be interrupted for a 9 minute period. 1 Press the SNOOZE button (5), after 9 minutes the radio or alarm buzzer will sound again. 2 3 4 5 To set the sleep function Your clock radio is equipped with a sleep function that will turn the radio on and switch it off automatically after a set period of time from between 59 minutes to 1 minute. Pressing the hour button (6) will extend the sleep time to 1 hour 59 minutes. 1 Press the SLEEP button (4) the LED display (10) will show 0:59 sleep time at the same time the radio will come on and stay on for 59 minutes. Press and hold the SLEEP button (4) whilst pressing the MINUTE button (7) or HOUR button (6) the sleep time shown on the LED display (10) will start descending. Release all buttons when the desired sleep time is shown on the LED display (10). After the set sleep time has elapsed, the radio will automatically switch off. To switch off before the set sleep time has elapsed press the SNOOZE button (5). Ensure the station you select will be transmitting at the preset alarm time. Wake up to the alarm buzzer In order to check that the correct alarm time has been set press the ALARM button (3). [. . . ] Refer any servicing to qualified personnel. Morphy Richards Limited Talbot Road Mexborough South Yorkshire S64 8AJ The lightning flash with arrowhead symbol within the triangle is a warning sign alerting the user of `dangerous voltage' inside the unit. Your post office will provide a certificate of posting. If you need any further advice, please call our Helpline (UK local rate) on: 08450 777700 (Mon-Fri) The exclamation point within the triangle is a warning sign alerting the user of important instructions accompanying the product. To prevent fire or shock hazard do not expose this apparatus to dripping or splashing. STMX 1908 Issue 1 05. 00 Imported by : Morphy Richards Ltd, Talbot Road, Mexborough, S64 8AJ P. 7 [. . . ]