User manual MORPHY RICHARDS IB75221

[. . . ] · Do not use any lead, switch or cord other than the one supplied with this blanket. · Not intended for medical use in hospitals. Care instructions · Examine frequently for any signs of wear or damage to the blanket, switch or cord. In case of damage or misuse, cease using and contact the Morphy Richards aftersales service helpline. (see page 7) · During the summer, the blanket can be used to air the mattress. [. . . ] WARNING: Only the electric blanket should be connected to the dual 3 Switch 11 1100 Rev 1 15/4/05 1:25 PM Page 4 Fitting instructions Fitted underblanket with elasticated corner tapes 1 Place the mattress cover directly on the mattress with the control switch end at the head of the bed. 2 Turn the elastic corners underneath the mattress to secure in place (see diagram A). 3 Ensure all creases are smoothed out. A Switch control Note: Braille markings are located on the back of the switch. , These three settings automatically turn the heat off after the selected time 12 hours 3 hours 1 hour / Power 'ON' light · Automatically switches the blanket on 3 hrs before you go to bed High heat setting (PRE-HEAT) ¤ Low heat setting (ALL NIGHT) < Heat setting Timer & 'Off' selection slider indicator Red = High heat Green = Low heat fl Blanket 'Off' position fi Sleep button Allows you to re-heat the bed through the night once a timer setting has switched off. > Heat selection slider 4 Switch 11 1100 Rev 1 15/4/05 1:25 PM Page 5 How to use 1 Ensure the blanket is fitted to the bed correctly. 2 Plug the power lead into the closest socket, using an extension lead if needed to ensure that the lead is not stretched. Sleep button 1 Use this button to turn the heat on for 30 minutes when the timer has switched the heat off. 3 The small light at the base of the switch will flash to indicate that the sleep function has been activated. 4 After 30 minutes the light will stop flashing and the heat will switch off. · Note: This function will only operate if the blanket is switched to a timer off setting, which has reached the end of the time period. It will not work if the switch is at the OFF 'O' position. Preheating the bed 1 Turn the blanket on by setting one of the timer off settings /, < or Â. 2 Set the heat setting on the control switch to maximum heat, the light indicator will show a red light to indicate that the preheating has been selected. Allow approximately 10-20 minutes for a light heat and a further 20-30 minutes for the blanket to heat the bed thoroughly, although this time may vary depending on room temperature. Setting the timer 1 To program the heat to turn on in 3 hours time, move the timer button to the unfilled 3 symbol . 2 When you get into bed, change the heat level to low, all night level. The heat will turn off after 9 hours, unless an alternative timer off setting or the OFF 'O' position is selected. 3 To program the heat to turn off after a set number of hours, move the timer button to the filled hour symbol /<Â. Note: The timer function will switch the blanket off after the selected time. Timer must be switched to the OFF position before setting a further time. All night use 1 Select the required timer off setting /, < or  hours. 2 Set the heat setting on the control switch to LOW heat, the heat setting indicator will show a green light. This setting will provide safe and comfortable heat to sleep on all night. WARNING: Always ensure that the heat setting is moved to the OFF position when you get up the next day. Braille markings · Braille markings are located on the back of the switch to help identify the direction of the heat level in the dark, or if visually impaired. · The highest heat level pre-heat is identified by 3 raised nodules mid level by 2 raised nodules low level (all night) by 1 raised nodule 5 Switch 11 1100 Rev 1 15/4/05 1:25 PM Page 6 Washing instructions WARNING: Before washing ensure that you detach all the controls from the blanket. · Do NOT dry clean · Do NOT iron 1 Measure the blanket so it can be stretched back to its original size whilst wet. [. . . ] If a low setting is not available, follow instructions for the drying under 'machine washing' section. B 6 Switch 11 1100 Rev 1 15/4/05 1:25 PM Page 7 After sales service If the blanket fails to operate, check the following before returning: 1 Ensure that the plug and socket have not become disconnected. For further help and advice, please contact our Helpline. Helpline Should you need any advice on using the product, please contact our helpline, 8:30 - 5:00 Mon - Thurs 8:30 - 4:00 Fri Tel: 0870 060 2616 0870 060 2616 1800 409089 Alternatively, please write to Morphy Richards Consumer Care or email us on: customercare@morphyrichards. co. uk 7 Switch 11 1100 Rev 1 15/4/05 1:25 PM Page 8 Your three year guarantee It is important to retain the retailers receipt as proof of purchase. Please quote the following information if the product develops a fault. These numbers can be found on the rating label attached to the blanket. [. . . ]