User manual MORPHY RICHARDS IB75114

[. . . ] · Do not use any lead, switch or cord other than the one supplied with this blanket. · Not intended for medical use in hospitals. Care instructions · Examine frequently for any signs of wear or damage to the blanket, switch or cord. In case of damage or misuse, please return immediately following instructions under servicing. · During the summer, the blanket can be used to air the mattress. [. . . ] · WARNING: Ensure the blanket is not folded, rucked or creased. When in use do not cover with pillows. Mattress covers with elasticated corner tapes 1 Place the mattress cover directly on the mattress with the control switch end at the head of the bed. 2 Turn the elastic corners underneath the mattress to secure in place (see diagram B). · Ensure all creases are smoothed out. Fitting instructions 1 Place the blanket directly on the mattress, with the control switch end at the head of the bed. · The blanket must be secured to the mattress in the following manner. Place the blanket directly on the mattress and ensure that a space of 10-15cm (4-6 inches) is left between the bottom edge of the blanket and mattress (see diagram A). A B 10-15 cm 4-6 inches 4 S7 Rev 2 21/7/04 1:56 PM Page 5 Switch control Features / Illuminated heat setting light (Red for preheat level, green for safe all night level) ¤ Variable heat levels (For exact heat preference) < Braille markings (located on the back of the switch) > Timer off (Automatically turns the heat off after the number of hours selected) fi Timer on (Automatically turns the heat on in 3 hours time) fl Off setting Sleep button (Turns the heat on for 30 minutes to help you drop off to sleep or to air the bed in the morning) · Power `on' indicator light > · ¤ < fi fl / How to use 1 Ensure the blanket is fitted to the bed correctly. 2 Plug the power lead into the closest socket, using an extension lead if needed to ensure that the lead is not stretched. All night use 1 Select the required timer off setting. This setting will provide safe and comfortable heat to sleep on all night. · This setting will provide safe and comfortable heat to sleep on all night. WARNING: Always ensure that the heat setting is moved to the OFF position when you get up the next day. Preheating the bed 1 Turn the blanket on by setting one of the timer off settings /, < or Â. 2 Set the heat setting on the control switch to maximum heat, the light indicator will show a red light to indicate that the preheating has been selected. Allow approximately 10-20 minutes for a light heat and a further 20-30 minutes for the blanket to heat the bed thoroughly, although this time may vary depending on room temperature. Braille markings · Braille markings are located on the back of the switch to help identify the direction of the heat level in the dark, or if visually impaired. · The highest heat level pre-heat is identified by 3 raised nodules mid level by 2 raised nodules low level (all night) by 1 raised nodule 5 S7 Rev 2 21/7/04 1:56 PM Page 6 Sleep button 1 Press this button to turn the heat on for 30 minutes. The light will flash to indicate that the sleep function has been selected, and it will automatically turn off after 30 minutes. This is ideal to help you get back to sleep if you wake in the night and are cold, or to air the bed in the morning. · Note: This function will only operate if the blanket is switched to a timer on or off setting, not if the switch is at the OFF position. 2 Only use in a washing machine with a drum large enough to take the blanket without forcing it in. Machine washing 40º Setting the timer 1 To program the heat to turn on in 3 hours time, move the timer button to the unfilled 3 symbol . 2 When you get into bed, change the heat level to low, all night level. The heat will turn off after 9 hours, unless an alternative timer off setting is selected. 3 To program the heat to turn off after a set number of hours, move the timer button to the filled hour symbol /<Â. For example, to set to turn heat off after 1 hour, move the button to the 1 /. [. . . ] In the case of damage, or for routine inspection every 2 years, return the blanket to the service department (see address below). A standard service charge (inclusive of packing and return carriage) is made for routine inspection where no repair is found to be necessary. If the blanket fails to operate, check the following before returning: 1 Ensure that the plug and socket have not become disconnected. Service department Waterside Mill Langham Street Rosegrove Burnley BB12 6AL Republic of Ireland c/o Dimpco Ltd Airport Road Cloghran Co. [. . . ]