User manual MORPHY RICHARDS IB73360

[. . . ] away from the floor nozzle whenever the cleaner is connected to the mains. Disconnect from the mains supply before attempting to clear blockages, clear the brush or replace the belt. Mains lead · Do not allow the mains lead to become strained or run this appliance over it. · If the electrical cable becomes damaged the complete cable assembly must be replaced. Do not attempt this task yourself, contact Morphy Richards using the helpline number. Electrical requirements Check that the voltage on the rating plate of your appliance corresponds with your house electricity supply which must be A. C. [. . . ] · Never have the brushes set too low such that the cleaner is hard to push. B C Using attachments Follow steps 1-4 but set the carpet height adjustment knob to the TOOLS setting. · Push the required attachment firmly onto the end of the hose. · If additional length is required, attach one or both extension tubes. · IMPORTANT: Always fix the hose clip ~ to the main body slot Ë when using the hose D min max 4 VC73360MUK-CyclonicBaglessRev3 3/11/05 4:41 pm Page 5 and tools. · Never over extend the hose such that the cleaner is pulled over. IMPORTANT: Turning the cleaner sideways helps prevent the cleaner being pulled along by the stretch hose. Emptying Empty the dust canister regularly even if it does not look full this will maintain the performance. 1 Remove the front cover by lifting the cover release lever ¤ E. 2 Lift-up the dust canister release Î and pull the canister away from the main body. 4 Turn the lid 1/4 turn anti-clockwise to unlock, lift off the lid with pleated filter, Ì put to one side. F 5 Lift out the central mesh filter Ô from the dust canister Ó G. 9 Re-fit pleated filter with lid into the dust canister by lining up the two arrows and turning the lid 1/4 turn clockwise to lock. Using & cleaning turbo nozzle (Certain models only) Attach the turbo nozzle to the hose end connector Í for use on upholstery and stairs. If they are tightly wound around the brush carefully snip the fibres with scissors, being careful not to damage the brush bar, pull away from the brush bar and dispose. Î ¤ E < F G Ì Ï Ô Ó 5 VC73360MUK-CyclonicBaglessRev3 3/11/05 4:41 pm Page 6 10 Re-fit dust canister into cleaner and push to lock into position. Then re-fit front cover. Safety cut-out If the cleaner overheats a motor protection thermostat will automatically switch the motor off. If this happens, switch the cleaner off, unplug from the power supply and leave the cleaner to cool for at least 30 minutes. Check the airways for blockages, empty dust canister and clean the filters before restarting. underneath the dust canister 1 Remove the dust canister. The filter may also be washed in water (no detergents) but must be totally dry before refitting. 3 Replace the filter Exhaust filter I Cleaning the filters To maintain suction the pleated filter must be shaken clean each time the dust canister is emptied. Failure to clean the filter will reduce suction and could damage the motor if used for a prolonged period. If the filters become damaged they must be replaced. The exhaust filter is located below the dust canister compartment. 2 Remove the exhaust filter Ú by pulling forward at the top and lift it away. 3 Take the filter out of the cage and shake vigorously over a dustbin. 4 Replace the filter and front cover. Changing the belt If the brush bar stops rotating it is likely that the drive belt has snapped (usually because the brush has been stalled). [. . . ] 3 Repairs have been attempted by persons other than our service staff (or authorised dealer). 4 Where the appliance has been used for hire purposes or non-domestic use. 5 Morphy Richards are not liable to carry out any type of servicing work, under the guarantee. 6 Consumables such as the filters and belt are not covered by the guarantee. [. . . ]