User manual MORPHY RICHARDS IB73106

[. . . ] · Do not store the appliance near hot ovens or heating appliances. Electrical requirements Check that the voltage on the rating plate of your charger unit corresponds with your house electricity supply which must be A. C. For appliances with fitted plug If the socket outlets in your home are not suitable for the plug supplied with this appliance the plug should be removed and the appropriate one fitted. Warning: The plug removed from the mains lead, if severed, must be destroyed as a plug with a bared flexible cord is hazardous if engaged into a live socket outlet. Should the fuse in the 13 amp plug require changing a 13 amp BS1362 fuse must be fitted. Main lead · Do not allow the mains lead to become strained or run this appliance over it. [. . . ] Attach to the turbo nozzle directly to the hose handle Í to remove stuborn pet hairs from upholstery or small areas of carpet. (Turbo nozzle is designed for small areas only for example pet beds and chairs) WARNING Do not attach the turbo nozzle to the extension tubes. 4 Hand held vac rev 3 73106/07 4/11/05 1:32 PM Page 5 Cleaning turbo nozzle (pets models only) G If the turbo nozzles rotating brush becomes entangled with hair it may require taking apart and cleaning 1 Unclip the top half of the nozzle by pulling the upper casing out slightly and lifting off. E E After re-assembly fit turbo nozzle on unit and ensure the brush bar is rotating correctly. Assembling the product Assembling Assembly Vacuum , Clear out any blockages /pet hair, remove all components. and clean if necessary. 2 The main turbo wheel has a removable collar, this must be re-assembled correctly, other wise the nozzle will not go back together. 3 To re-assemble nozzle, take the brush bar with the toothed belt positioned over the track on the bar (notice the rectangular · · Î · Â , , Í Ò Ì Í Ï F Blower Ê · , Note Make sure the correct end is fixed to the blower adapter, (smooth end). Nozzle locators on either side of the brush bar). F Slot the brush bar into the relevent tracks on either side of the lower casing. Ensuring that the turbo wheel is correctly placed, loop the toothed wheel through the belt and lower the turbo wheel into the grove, provided in the lower casing. 4 Ensuring that the brush bar, the turbo wheel and the belt are correctly located and positioned, take the top casing and position the slots over the teeth at the front of the lower casing and clip back into position. When using the brush nozzle Ò to get extra suction place your finger over the hole. This is only for vacuuming H H 5 Hand held vac rev 3 73106/07 4/11/05 1:32 PM Page 6 Dust disposal To obtain the best results from your cleaner be sure to check and empty the dust compartment regularly, otherwise the airflow and cleaning power will be reduced and you may damage your cleaner. 1 Ensure the cleaner is switched off and disconnected from the mains supply. 2 Hold over a dustbin and press in the dust compartment release button fl, the dust compartment door will automatically drop down. Shake the vacuum to release the dirt and make sure it is completely empty. I 2 Pull the pleated hepa filter Ô out of the mesh filter cover and clean both by gently brushing over the dustbin. DO NOT USE DETERGENTS 3 Replace the pleated filter into the mesh filter cover L Hepa Filter cleaning Warning: The dust compartment must be emptied BEFORE the Hepa filter is removed. 1 Once the dust compartment is empty, remove the pleated hepa filter Ô and mesh filter by pushing the tab to release. J Making sure the yellow tab on the Hepa Filter moulding is adjacent to the clip on the mesh filter cover L and replace back into the cleaner. Blocked filters will reduce the airflow to the motor, should the airflow become substantially blocked, the product will then be liable to overheat and the thermal fuse will activate. Should this activate, the product will stop functining, unplug the product and allow it to cool down (ths can take between 30-40 minutes depending on the ambient temperature conditions). Inserting Hepa Filter M M I K Warning: Make sure that the Hepa filter has been placed in correctly. J DO NOT USE THE PRODUCT WITHOUT THE HEPA FILTER FITTED. IMPORTANT · All filters should be checked regularly for signs of damage, preferably after each cleaning task. The filters must be replaced immediately if they become 6 Hand held vac rev 3 73106/07 4/11/05 1:32 PM Page 7 · Always disconnect the cleaner from the mains when checking or replacing the filters. [. . . ] We are likely to be more help than the store from where it was bought. Please have the following information ready to enable our staff to help you. · Name of product · Model number as shown on the underside of the appliance. 8 Hand held vac rev 3 73106/07 4/11/05 1:32 PM Page 9 Your two year guarantee It is important to retain the retailers receipt as proof of purchase. Please quote the following information if the product develops a fault. [. . . ]