User manual MORPHY RICHARDS IB71051

[. . . ] · Never use the appliance to vacuum hot ashes, broken glass, sharp objects or liquids. Mains lead · Do not allow the mains lead to become strained or run this appliance over it. · If the electrical cable becomes damaged the complete cable assembly must be replaced. Do not attempt this task yourself, contact Morphy Richards using the replacement parts number on the front of this leaflet. Electrical requirements Check that the voltage on the rating plate corresponds with your house electricity supply which must be A. C. If the socket outlets in your home are not suitable for the plug supplied with this appliance the plug should be removed and the appropriate one fitted. [. . . ] The crevice tool Í (for awkward places, behind radiators etc) and the upholstery nozzle Î with clip on brush Ï (for curtains and upholstery) are stored in the tool drawer , . The crevice tool is used for hard surfaces, pelmets, delicate objects etc C. Stair cleaning hose Ó An additional stretch hose is also provided for use on stairs. Fit the hose to the cleaner by inserting the hose end into the hose inlet. WARNING: For safety, always leave the cleaner at the bottom of the stairs and clean upwards. B Í C Î Ï 4 71051 Rev 3 17/2/05 12:07 PM Page 5 Controls Power The on/off control is operated by the foot pedal >. Variable power A sliding switch fi varies the suction power as required. For example, maximum suction can be used for cleaning carpets, hard floors etc. Suction can also be controlled using the airflow regulator on the handle Â. Closed for maximum suction, open for reduced suction. 1 Remove the dust container from the product by pressing the dust container release button fl and pulling the dust container away from the product. D 2 Holding the dust container over a dustbin slide the dust release cover forwards and press the dust release button as shown E, the bottom of the dust container will drop down to release the dirt. 3 Close the bottom of the dust container by pressing the base upwards until it clicks into place. The dust release cover will slide back into place automatically. Allergy sufferers If the allergy sufferer is emptying the product it is recommended that the container is placed into a plastic bag to empty. 1 Place the container inside the plastic bag, releasing the container with one hand whilst holding the top of the bag closed with the other, leave the dust to settle for a few seconds before carefully removing the empty container. The plastic bag can then be sealed and disposed of. Automatic cable rewind After use, unplug and press the cable rewind button ¤ to retract the cable. WARNING: When using the cable rewind, always hold the plug as the cable will rewind quickly. Dust disposal To obtain the best results from your cleaner empty the dust container regularly, otherwise the airflow and cleaning power will be reduced. D E 5 71051 Rev 3 17/2/05 12:07 PM Page 6 Cleaning the motor protection filter 1 Remove the dust container from the product by pressing the dust container release button fl and pulling the container away from the product. 2 Remove the motor protection filter from the top of the dust container by pushing the filter release switch to release the filter and lift the filter out of the container from the top F. The filter can be gently knocked against the side of the dustbin to remove excess dust. Use the filter cleaning brush È to remove dirt from between the pleats. 3 To re-fit the filter, drop the cartridge into the hole in the top of the dust container. Ensure the top of the filter is located under the lug and push the filter release switch to allow the filter to drop into place. The filter release switch will then automatically flick back when released to lock the filter in place. The filter should be regularly washed in cold water and left to air dry before inserting back into the machine. [. . . ] All Morphy Richards products are individually tested before leaving the factory. In the unlikely event of any appliance proving to be faulty within 28 days of purchase it should be returned to the place of purchase for it to be replaced. If the fault develops after 28 days and within 24 months of original purchase, you should contact the Helpline number quoting Model number and Serial number on the product, or write to Morphy Richards at the address shown. You will be asked to return the product (in secure, adequate packaging) to the address below along with a copy of proof of purchase. [. . . ]