User manual MORPHY RICHARDS IB70280

[. . . ] If you cut off the plug and let go of the cable it will rewind into the machine therefore, you must pull out a length of cable and secure it before cutting off the plug and fitting a new one. WARNING: The plug removed from the mains lead, if severed, must be destroyed as a plug with bared flexible cord is hazardous if engaged into a live socket outlet. Should the fuse in the 13 amp plug require replacement, a BS1362 13 amp fuse must be fitted. Mains lead · Do not allow the mains lead to become strained or run this appliance over it. · If the electrical cable becomes damaged the complete cable assembly must be replaced. [. . . ] IMPORTANT: When cleaning on stairs, for convenience and safety, work from the bottom to the top with the desired accessory connected directly onto the hose handle. It is Controlling suction power Suction power can be adjusted using the handle suction control Á. Keep it closed for full suction and open for reduced suction. recommended not to use the extension tube. fl fl 5 Emptying the dust container IMPORTANT: To obtain best results from your cleaner it is important to empty the dust container and clean the filters regularly, otherwise the airflow and suction power will be reduced. If the dust container is not full and performance deteriorates, first check if there are any blockages in the accessories or tubes. If these are clear, it is necessary to empty the dust container and clean the filter. Step 3 Holding the dust container over a dustbin, grip the tabs on the back of the filter, pull to remove and empty out the dust. Step 1 Remove the hose by pressing in the clips and pulling the hose away from the hose inlet. Step 2 Slide back the dust container release button ¤ and lift off the dust container using the folding handle. 4 Replace the clean filter, making sure that it is correctly fitted, then replace the dust container. IMPORTANT: Do not operate your cleaner without the filters fitted. 6 Cleaning the filter Everytime the dust container is emptied the filter should be cleaned. Pull the tabs at the side of the mesh filter cover to remove the pleated filter cover. Use the brush attached to the rear of the filter to brush the fine dust from between the filter pleats. Refit the mesh filter cover and reinstall the filter into the cleaner. The filter should also be washed regularly in warm water, but do not use detergent. Allow to dry naturally and ensure it is totally dry before replacing it. An additional filter (not filter cover or brush) is provided allowing continued use while one filter is washed and dried. When changing the filters over ensure the filter cover is fitted to the filter that is being placed in the machine. Note: A protection device maintains the air-flow to the motor if the filters become blocked. If this happens, clean the filter and clear any blockage, the sound of the cleaner will then return to normal. WARNING: Never use the appliance without the filters installed, otherwise damage to the product may occur which would not be covered by the guarantee. 7 Cleaning the motor protection filter The motor protection filter should be cleaned regularly by sliding out of its location and shaking rigorously to dislodge any dust. The motor protection filter can also be washed in warm water and left to air dry. IMPORTANT: Do not use detergents and ensure filter is thoroughly dry before re-inserting into the machine. Cleaning and replacing the exhaust filter The exhaust filter should be cleaned regularly by sliding out of its location. The exhaust filter is non washable and should be replaced every 6 months. Parts may be purchased from specialist retailers or by calling the replacement parts telephone line. 8 Storage and maintenance Unplug the cleaner from the mains before cleaning. Press the cable rewind button ·, to rewind the cord into the storage unit. The vacuum cleaner and all the accessories can be cleaned using a damp cloth and wiped dry. [. . . ] In the unlikely event of any appliance proving to be faulty within 28 days of purchase it should be returned to the place of purchase for it to be replaced. If the fault develops after 28 days and within 24 months of original purchase, you should take the appliance to your nearest service agent. A list containing details of your nearest service agent is included with your appliance but please contact the helpline quoting model number and serial number should you require further assistance. Repair or replacement of the product is subject to the exclusions set out below (1-5). [. . . ]