User manual MORPHY RICHARDS IB70250

[. . . ] Please note The models described in these instructions are similar in most respects but some of the features described apply to specific models only. To obtain the best results from your cleaner please read these instructions carefully and keep them in a safe place for future reference. European conformity information A sample of this product has been tested and found to be in conformity with the following European Directives: 73/23/EEC 93/68/EEC 89/336/EEC Low Voltage CE Marking EMC directive Unwanted products and the environment Should you find one day that your product needs replacement, or is of no further use to you, think of the protection of the environment. Your local Service Dealer will accept your old products and will dispose of them in an environmentally safe way. Buying genuine Goblin accessories the easy way the letter `N' or is coloured black. [. . . ] The defective part will be repaired or, at our option, replaced free of charge for labour and materials provided that: · the cleaner has been operated on an electricity supply which matches that shown on the rating plate. · only Genuine Goblin parts have been used and have been fitted correctly. · the cleaner has not been used for commercial applications. Pack of 2 Pack of 5 Pack of 1 Pack of 2 Pack of 2 P/N 87383-70 Rev 03/01 Republic of Ireland 01 842 4833 The After Sales Division Dimpco Ltd Cloghran County Dublin Ireland 9180624 Part number 9056024 9180324 9180424 9180524 5330575 0311690 0071490 0073690 0073590 3770290 3770570 3779870 Instructions 340 Series g Using your Goblin vacuum cleaner Assembly To fit the hose to the cleaner, insert the hose end into the hose inlet < until it clips securely into position. The hose handle features a regulator which allows the suction to be reduced as required. · turn fully clockwise for maximum suction for carpets, hard floors etc. · turn anti-clockwise for reduced suction for upholstery and curtains. Cleaning and replacing the filters Motor protection filter This is in the dustbag compartment. Clean it everytime you change the dustbag and replace it after approximately 5 dustbag changes. G Stair Lock (certain models) This unique device (patent applied for) assists with stair cleaning. The special bracket , , found underneath, is lifted out as shown B and locked onto the stairs. In addition, the rear wheels are locked in position as further security. Please note When cleaning on stairs, for convenience and safety, work from the bottom to the top with the upholstery nozzle or crevice tool connected directly onto the hose handle. It is recommended that the extension tubes are not used. Attaching the accessories Fit the floor nozzle onto the end of the extension tube. The hard floor attachment (certain models) can be attached to the floor nozzle, to facilitate vacuuming hard floors. Other accessories are stored in the back of the cleaner and include: · upholstery nozzle for stairs, furniture; · crevice tool for awkward places, behind radiators etc. 1 Lift out the red filter as shown G and clean by tapping. B 2 Replace the filter by sliding it into position as shown H. Note The safety catch  prevents the cover being closed unless a motor protection filter is fitted. Automatic cable rewind (certain models) Reel out the cable fully. After use, unplug and press the foot pedal fl, holding the plug until fully rewound. H On/off The on/off control is operated by the foot pedal . Electronic suction regulator (certain models) This is a rotating knob · which allows the suction power of the cleaner to be set at the precise level required. For example: Replacing/emptying the dustbag To obtain the best results from your cleaner be sure to change the dustbag when necessary, otherwise the airflow and cleaning power will be reduced. When the dustbag condition indicator > shows fully red and performance deteriorates, first check if there are any blockages in the accessories or tubes. If these are clear, it is necessary to replace/empty the dustbag. C Exhaust filter Ê This is located on top of the motor housing J. [. . . ] 6 Slide the clip back onto the bottom of the dustbag and replace the dustbag into position ensuring the collar is firmly secured at the base E. 7 Pull forward as shown F so it locks under the plastic securing tab at the top. 9 Relocate the lid at the front (carrying handle /) end first and then close the cover securely. [. . . ]