User manual MORPHY RICHARDS IB42700

[. . . ] 6 Plastic filters for all Morphy Richards kettles and coffee makers are not covered by the guarantee. This guarantee does not confer any rights other than those expressly set out above and does not cover any claims for consequential loss or damage. This guarantee is offered as an additional benefit and does not affect your statutory rights as a consumer. All Morphy Richards Products are individually tested before leaving the factory. In the unlikely event of any appliance proving to be faulty within 28 days of purchase it should be returned to the place of purchase for it to be replaced. [. . . ] (Check by plugging in another appliance) 2 Warning: When in use, your iron should never be placed flat and left on an ironing board. 3 To prevent damage to the textile being ironed, follow the temperature guide carefully. 4 When ironing is complete, remove the plug from the socket, empty any remaining water from the tank, and allow to cool before storing. 5 If you drop or severely knock your iron this could cause internal damage even if the outside appears alright. 6 It is recommended that you use up one beaker of water by operating your iron's steam and shot of steam functions before ironing any clothes as some dripping may occur while your iron's steam system is activated. SAVE THESE INSTRUCTIONS 2 Electrical requirements Components of your iron Check that the voltage on the rating plate of your appliance corresponds with your house electricity supply which must be A. C. If the socket outlets in your home are not suitable for the plug supplied with this appliance, the plug should be removed and the appropriate one fitted. WARNING: The plug removed from the mains lead, if severed, must be destroyed as a plug with bared flexible cord is hazardous if engaged into a live socket outlet. WARNING: THIS APPLIANCE MUST BE EARTHED Should the fuse in the 13 amp plug require replacement, a BS1362 13 amp fuse must be fitted. < fifl/ ¤ > / Temperature control dial ¤ Temperature indicator light < Water tank cap > Soleplate fi Spray button (certain models only) fl Shot of steam button (certain models only) Steam on-off button/variable steam button Instructions for use Temperature Guide Heat setting markings on the adjustable control dial of all Morphy Richards irons match those of the International Textile Care Labelling Code. Symbol Control knob positions Fabric 6 Do not iron at all 7 (120°C Max) Cool q Nylon, Acetates E. g. If moisture required use damp cloth (Not Acetate) Dry and Spray 8 (160°C Max) Warm qq Wool, Polyester mixtures e. g. Polyester/Cotton 9 (210°C Max) Hot qqq Cotton, Linen Rayon, Rayon mixtures, e. g. Rayon/Linen Ironing With water in tank Without water in tank Fabrics requiring this setting usually require steam pressing for heavy cotton, denim etc Steam/spray & shot Jet clean Dry ironing 3 Before use Note: The Steam facility should only be used on garments which are suitable for ironing at 2 and 3 dot settings. (Garments marked with 2 dot recommendation should, if required, be ironed at the lower end of the steam range). If they don't you should follow the temperature guide on page 3, but be sure to test the temperature by ironing the hem of the garment or similar area first. If you turn the control dial down from a hot setting to a cooler setting, wait until the iron temperature has stabilised before you continue ironing. Temperature control Plug in the iron and switch on. Set the temperature control dial C to the temperature required, but don't start ironing immediately. If you wait a few minutes, the iron will stabilise at ST E the required setting. EAM RA N G Your Morphy Richards iron is fitted with an indicator light which will go on and off while your are ironing. This is perfectly normal as it shows that the iron is maintaining the heat setting you have chosen. For the correct temperature always set the control dial with the required setting at the bottom of the dial nearest the back of the iron. C Filling Before filling your iron make sure that it is not plugged in and ensure that the iron is in the `steam off' position. Fill using the beaker provided A. A Features of your iron Temperature indicator light The temperature indicator light shows that the iron is warming up. When the required temperature is reached the light will go out and will cycle on-off during operation. Your iron has a large capacity tank which can hold 2 beakers of water. [. . . ] This feature is especially useful for removing creases from hanging clothes, curtains, wall hangings, etc. H Variable steam (certain models only) If your iron is fitted with variable steam, the steam output can be varied from low to high. The high position is for ironing stubborn creases F High steam Auto shut-off (certain models only) If your iron is an `auto shut-off' model it will automatically turn your iron off within 60 seconds of not being used. If the iron is below the temperature set on the temperature control dial, the temperature indicator light will illuminate until the iron reaches the set temperature. AUTO SHUT-OFF IS NOT AN ALTERNATIVE TO UNPLUGGING THE IRON WHEN NOT IN USE. The mid position is for normal ironing Low steam The low position switches the steam off. Steam off 5 Emptying and storing When you have finished ironing unplug your iron. [. . . ]