User manual MORPHY RICHARDS IB42410

[. . . ] 6 Plastic filters for all Morphy Richards kettles and coffee makers are not covered by the guarantee. This guarantee does not confer any rights other than those expressly set out above and does not cover any claims for consequential loss or damage. This guarantee is offered as an additional benefit and does not affect your statutory rights as a consumer. All Morphy Richards Products are individually tested before leaving the factory. In the unlikely event of any appliance proving to be faulty within 28 days of purchase it should be returned to the place of purchase for it to be replaced. [. . . ] (Check by plugging in another appliance) 2 Warning: When in use, your iron should never be placed flat and left on an ironing board. 3 To prevent damage to the textile being ironed, follow the temperature guide carefully. 4 When ironing is complete, remove the plug from the socket, empty any remaining water from the tank, and allow to cool before storage. 5 If you drop or severely knock your iron this could cause internal damage even if the outside appears alright. 6 It is recommended that you use up to one beaker of water by operating your iron's steam and shot of steam functions before ironing any clothes, as some dripping may occur while the steam system is activated. SAVE THESE INSTRUCTIONS 2 Electrical Requirements Check that the voltage on the rating plate of your appliance corresponds with your house electricity supply which must be A. C. If the socket outlets in your home are not suitable for the plug supplied with this appliance, the plug should be removed and the appropriate one fitted. WARNING: The plug removed from the mains lead, if severed, must be destroyed as a plug with bared flexible cord is hazardous if engaged into a live socket outlet. Should the fuse in the 13 amp plug require replacement, a BS1362 13 amp fuse must be fitted. WARNING: THIS APPLIANCE MUST BE EARTHED. Instructions for use Temperature Guide Heat setting markings on the adjustable control dial of all Morphy Richards irons match those of the International Textile Care Labelling Code. Symbol Control knob positions Fabric 6 Do not iron at all 7 (120°C Max) Cool q Nylon, Acetates E. g. If moisture required use damp cloth (Not Acetate) Dry and spray 8 (160°C Max) Warm qq Wool, Polyester mixtures e. g. Polyester/Cotton 9 (210°C Max) Hot qqq Cotton, Linen Rayon, Rayon mixtures, e. g. Rayon/Linen Ironing With water in tank Without water in tank Fabrics requiring this setting usually require steam pressing for heavy cotton, denim etc Steam/spray & shot Jet clean Dry ironing 3 Components of your iron fifl < / · > / Temperature control dial ¤ Temperature indicator light < Filling cover > Soleplate fi Spray button fl Shot of steam button Variable steam control · Anti-scale cartridge (certain models only) Filling Before filling your iron make sure that it is not plugged in. Fill using the beaker provided A. ¤ A Before Use NOTE: The steam facility should only be used on garments which are suitable for ironing at 2 and 3 dot settings. When ironing with the steam facility at the 2 dot setting, the steam output should be set at the lower end of the steam range (see `Variable steam' section). If they don't you should follow the temperature guide on page 3, but be sure to test the temperature by ironing the hem of the garment or similar area first. If you turn the temperature control dial down from a hot setting to cooler setting, wait until the iron temperature has stabilised before you continue ironing. Your iron has a large capacity which can hold 2 beakers of water. After filling, close the filling cover to prevent any water escaping from the tank during ironing. Never use battery topping-up fluid or water containing any substances such as starch or sugar, or defrosted water from a refrigerator. If you live in a hard water area, and your iron is not fitted with an anti-scale device, the use of distilled or demineralised water is recommended. WARNING: When filling your iron with tap water always use the beaker provided. Never fill directly under the tap. Temperature Control Plug in the iron and switch on. Set the temperature control dial B to the temperature required, but don't start ironing immediately. If you wait a few minutes, the iron will stabilise at the required setting. [. . . ] Make a loose loop with the flex and wrap it around the iron using the cord clip to keep the flex in place. The iron must be cool before winding the flex and storing on its heel M. M Maintenance Jet cleaning Your iron has a built-in cleaning system designed to keep the water valve, steam chamber and steam vents clear of lint and loose mineral deposits. To operate, ensure that there is a little water in the tank, place the iron on its heel and turn the temperature control dial to the maximum setting. Wait for the temperature indicator light to go out, then unplug the iron and hold it about 6"(150mm) above the sink in the ironing position. [. . . ]