User manual MORPHY RICHARDS IB41510

[. . . ] It is in your interest to retain the retailers receipt as proof of purchase. Please quote the following information if the product develops a fault. Serial No. guarantee the appliance must have been used according to the manufacturers instructions. For example kettles should have been regularly descaled or an iron cord should have been stored as recommended by the instructions. [. . . ] Subject to the exclusions set out below (see `Exclusions') the faulty appliance will then be repaired or replaced and dispatched usually within 7 working days of receipt. If for any reason this item is replaced during the 2 year guarantee period, the guarantee on the new item will be calculated from original purchase date. Therefore it is vital to retain your original till receipt or invoice to indicate the date of initial purchase. To qualify for the 2 year Ensure the iron is thoroughly dry then place in the bag provided. Important : The flex can be damaged if wound too tightly around the iron after use. The iron must be cool before winding the flex and storing on its heel. Emptying and Storing When you have finished ironing, unplug your iron. Remove the water inlet cover and empty any remaining water out of the filling hole. Replace the water inlet cover. 2 7 Electrical requirements Check that the voltage on the rating plate of your appliance corresponds with your house electricity supply which must be A. C. If the socket outlets in your home are not suitable for the plug supplied with this appliance the plug should be removed and the appropriate one fitted. IMP0RTANT : THE PLUG REMOVED FROM THE MAINS LEAD, IF SEVERED, MUST BE DESTROYED AS A PLUG WITH A BARED FLEXIBLE CORD IS HAZARDOUS IF ENGAGED INTO A LIVE SOCKET OUTLET. Should the fuse in the 13 amp plug require replacement, a 13 amp BS1362 fuse must be fitted. WARNING : THIS APPLIANCE MUST BE EARTHED. Components of your iron Textiles and clothes are supposed to carry ironing instructions. If they don't you should follow the fabric guide on page 4, but be sure to test the temperature by ironing the hem of the garment or similar area first. If you turn the control dial down from a hot setting to a cooler setting, wait until the iron temperature has stabilised before you continue ironing. Filling 1 Temperature control dial Temperature indicator light Sole plate Water tank Water inlet cover Steam control 2 Before filling the iron with water, ensure that the iron is unplugged is set to and the steam control . Pull the water inlet cover out and pour the water through the , filling hole into the water tank . In using the beaker provided hard water areas the use of distilled or demineralised water is recommended. Never use battery topping-up fluid or water containing any substances like starch or sugar, or defrosted water from a refrigerator. Instructions for use Temperature guide Heat setting markings on the adjustable control dial of all Morphy Richards irons match those of the international Textile Care Labelling Code. Symbol (120 C Max) Cool (160 C Max) Warm (210 C Max) Hot Control knob positions Fabric Do not iron at all Nylon, Acetates e. g. If moisture required use damp cloth (Not Acetate) Wool, polyester mixtures e. g. Rayon/Linen Fabrics requiring this setting usually require steam pressing for heavy cotton, denim etc o o o Dial pointer Before use It is recommended that you use up one beaker of water by operating your iron's steam and shot of steam functions before ironing any clothes as some dripping may occur while your iron's steam system is first activated. Note : The steam facility should only be used on garments which are suitable for ironing at the 3 dot setting. 3 Ironing With water in tank Dry Steam /shot of steam Dry ironing Without water in tank 4 5 4 Always pour out the remaining water after use. Dry ironing You can also use your iron as a dry iron only. Steam control Important safeguards WARNING : When filling your iron with tap water always use the beaker provided. Never fill directly under the tap. Temperature control Plug in the iron and switch on. Set the temperature control dial to the temperature required, but don't start ironing immediately. [. . . ] 3 To prevent damage to the textile 6 Do not allow cord to touch hot being ironed, follow the tempera surfaces. loosely around the iron before 4 When ironing is complete, remove storing. the plug from the socket, empty 7 Always disconnect the iron from any remaining water from the tank, the electrical socket when filling and allow to cool before storage. with water or emptying and when 5 If you drop or severely knock not in use. [. . . ]