User manual MORPHY RICHARDS IB40715

[. . . ] This guarantee is offered as an additional benefit and does not affect your statutory rights as a consumer. · This guarantee is valid in the UK and Ireland only. Semi-electronic iron steam/spray/shot Please read and keep these instructions All Morphy Richards products are individually tested before leaving the factory. In the unlikely event of any appliance proving to be faulty within 28 days of purchase it should be returned to the place of purchase for it to be replaced. If the fault develops after 28 days and within 24 months of original purchase, you should contact the Helpline number quoting Model number and Serial number on the product, or write to Morphy Richards at the address shown. [. . . ] · Always disconnect the iron from the electrical socket when filling with water or emptying, and when not in use. · Do not operate the iron with a damaged cord or if the iron has been dropped or damaged. To avoid the risk of electric shock, do not disassemble the iron, but telephone Morphy Richards for advice. Incorrect reassembly can cause a risk of electric shock when the iron is used. Do not store in the box, but in an upright position, so that any drops of water remaining cannot leak out and discolour the soleplate. Important: The flex can be damaged if wound too tightly around the iron after use. The iron must be cool before winding the flex and storing on its heel. Helpline If you have any difficulty with your appliance, do not hesitate to call us. We are more likely able to help than the store from where you bought it. Please have the following information ready to enable our staff to deal with your query quickly. · Name of the product · Model number as shown on the underside of the appliance. Location · Do not use outdoors. Special instructions · If your iron does not work, check the following points: Has the temperature control been set to the required temperature?· WARNING: When not in use, your iron should never be placed flat and left on an ironing board. · To prevent damage to the textile being ironed, follow the temperature guide carefully. · When ironing is complete, remove the plug from the socket, empty any remaining water from the tank, and allow to cool before storage. · If you drop or severely knock your iron this could cause internal damage even if the outside appears alright. · It is recommended that you use up one beaker of water by operating your iron's steam and shot of steam functions before ironing any clothes as some dripping may occur while your irons steam system is activated. Children · Children do not understand the dangers associated with operating electrical appliances. · Close supervision is necessary when any appliance is used near children. Personal safety · WARNING: Burns can occur from touching hot metal parts, hot water or steam. Use caution when you turn a steam iron upside down, there may be hot water in the water tank. · WARNING: To protect against the risk of electric shock do not put the appliance in water or in any other liquid. · Do not use the vertical steam feature on clothes that are being worn. · Do not leave the iron unattended whilst plugged in or on an ironing board. · The socket should always be off before plugging or unplugging from the socket. Never yank the cord to disconnect from the socket, instead, grasp plug and pull to disconnect. Emptying and storing When you have finished ironing, unplug your iron. Ensure that the variable steam control is set at the `0' position, lift up the fill cap and empty any remaining water out of the filling hole. 2 7 Job: 40715 Rev 1 -- Color: Composite -- Signature 2, Sheet 1, Front -- Plate 3 Shot of steam Press the shot of steam button ¤ to obtain a burst of extra steam for ironing out creases in heavy material such as denim etc. [. . . ] WARNING: This appliance must be earthed. Instructions for use Temperature guide Heat setting markings on the function console panel of your Morphy Richards irons match those of the International Textile Care Labelling Code. Symbol Life long anti-scale system The life long anti-scale system reduces scale deposits and helps prolong the life of the iron. (120°C Max) Cool Control knob positions Fabric Do not iron at all Nylon, Acetates e. g. Tricel/Polyester Iron on wrong side if moisture required use damp cloth (Not Acetate) Dry and spray (160°C Max) Warm (210°C Max) Hot Wool, Polyester mixtures e. g. Rayon/Linen Fabrics requiring this setting usually require steam pressing for heavy cotton, denim etc. Ironing With water in tank Steam/spray/shot of steam Jet clean Without water in tank Dry ironing 6 3 Job: 40715 Rev 1 -- Color: Composite -- Signature 2, Sheet 1, Back -- Plate 4 Components of your iron / ¤< It is always a good idea to begin with cool fabrics and work up to higher settings. An iron heats up quicker than it cools down so you'll save time and electricity. Temperature control B Increase temperature Decrease temperature Filling , 1 Make sure that the iron is not plugged in and then set the variable steam control / to the `0' position before filling the iron with water. [. . . ]