User manual MORPHY RICHARDS IB40620

[. . . ] 10 Do not use the vertical steam feature on clothes that are being worn. 11 Do not leave the iron unattended whilst plugged in or on an ironing board. Use caution when you turn a steam iron upside down, there may be hot water in the water tank. Special instructions 1 If your iron does not work, check the following points: Has the temperature control been set to the required temperature?2 Warning : When not in use, your iron should never be placed flat and left on an ironing board. [. . . ] 4 · To indicate that the iron is heating up arrow above the thermometer symbol will flash. · To indicate that the iron is cooling down the arrow below the thermometer will flash. This is perfectly normal as it shows that the iron is maintaining the heat setting you have chosen. DIGITAL SYEAM 4 13/8/02, 12:29 PM · When your iron reaches the correct temperature for the first time it will beep twice. The arrow icon will also stop flashing to show that the iron has reached the correct temperature. To adjust the temperature setting depress the a beep will be audible FUNCTION button every time the function button is pressed. The temperature will cycle up and down (MAX - 3 dot - 2 dot - 1 dot - 2 dot. . . etc) and will be indicated on the LCD display. Variable Steam Fill the iron with water as described in "Filling", page 4 and insert the plug into the electrical socket. Press the function button until the 2-dot, 3-dot or MAX setting is displayed (as required) and rest the iron on it's heel whilst it warms up. The heating up arrow icon will disappear when the iron is at the correct temperature. The steam facility should only be used on garments which are suitable for ironing at the 2 dot, 3-dot or MAX setting. High Low Off It is always a good idea to begin with `cool' fabrics and work up to higher settings. An iron heats up quicker than it cools down so you'll save time and electricity. Shot of steam Press the shot of steam button to obtain a burst of extra steam for ironing out creases in heavy material such as denim etc. The shot of steam can be used whilst dry ironing, providing there is water in the tank, and the temperature control is set to the steam position. Note : For optimum steam quality, do not operate the shot more than three times in succession. Features of your iron Dry ironing You can use your iron as a dry iron only. Make is set to the sure the variable steam control "0" symbol. The spray feature may be used provided there is water in the tank (see filling section). You do not need to put any water in the tank when dry ironing only. Vertical steam Hold the iron in a vertical position between 1 cm and 2 cm away from the item. This feature is especially useful for removing creases from hanging clothes, curtains, wall hangings, etc. Spray Press the spray button and aim the spray of water at stubborn creases. You can do this whilst dry ironing providing there is water in the tank. When using the water spray it may be necessary to push the button a few times to get the spray pump primed. 5 DIGITAL SYEAM 5 13/8/02, 12:29 PM Drip stop Your iron is fitted with a no drip system which is designed to prevent water escaping from the soleplate when the iron is too cold. During use, the no drip system may emit a loud click, particularly during heat-up or whilst cooling down. This is perfectly normal and indicates that the system is functioning correctly. Filling / Refilling your anti-scale cartridge 1 Empty any remaining water from the tank, (see emptying and storing section). 2 To remove the anti- scale cartridge from the iron push in the clips on either side of the cartridge and pull it out. 3 Remove the cartridge lid as follows, hold the cartridge upright and gently squeeze it by the retaining lugs. 6 Replace the lid back on the cartridge by aligning the holes with their lugs and pressing down until it clicks shut on both sides. 8 Your iron is now ready to use and the water tank can be filled. Auto shut off feature Your iron is equipped with an automatic shutoff feature which will cut the power to the iron if left for 30 seconds in the horizontal (ironing) position or after 8 minutes standing on its heel. [. . . ] · This guarantee is valid in the UK and Ireland only. All Morphy Richards products are individually tested before leaving the factory. In the unlikely event of any appliance proving to be faulty within 28 days of purchase it should be returned to the place of purchase for it to be replaced. If the fault develops after 28 days and within 24 months of original purchase, you should contact the Helpline number quoting Model number and Serial number on the product, or write to Morphy Richards at the address shown. You will be asked to return the product (in secure, adequate packaging) to the address below along with a copy of proof of purchase. [. . . ]