User manual MORPHY RICHARDS IB40616

[. . . ] This guarantee is offered as an additional benefit and does not affect your statutory rights as a consumer. · This guarantee is valid in the UK and Ireland only. All Morphy Richards products are individually tested before leaving the factory. In the unlikely event of any appliance proving to be faulty within 28 days of purchase it should be returned to the place of purchase for it to be replaced. If the fault develops after 28 days and within 24 months of original purchase, you should contact the Helpline number quoting Model number and Serial number on the product, or write to Morphy Richards at the address shown. [. . . ] · Do not use the vertical steam feature on clothes that are being worn. · Do not leave the iron unattended whilst plugged in or on an ironing board. · The socket should always be off before plugging or unplugging from the socket. Never yank the cord to disconnect from the socket, instead, grasp plug and pull to disconnect. Loop cord loosely around the iron before storing. 2 Comfi iron 441375234 Rev 3 31/1/03 11:43 PM Page 4 Electrical requirements Check that the voltage on the rating plate of your appliance corresponds with your house electricity supply which must be A. C. If the socket outlets in your home are not suitable for the plug supplied with this appliance the plug should be removed and the appropriate one fitted. WARNING : The plug removed from the mains lead, if severed, must be destroyed as a plug with a bared flexible cord is hazardous if engaged into a live socket outlet. Should the fuse in the 13 amp plug require changing a 13 amp BS1362 fuse must be fitted. WARNING: THIS APPLIANCE MUST BE EARTHED. Instructions for use Temperature guide Heat setting markings on the adjustable control dial of all Morphy Richards irons match those of the International Textile Care Labelling Code. Symbol (120°C Max) Cool Control knob positions Fabric Do not iron at all Nylon, Acetates e. g. Tricel/Polyester Iron on wrong side if moisture required use damp cloth (Not Acetate) Dry and spray Wool, Polyester mixtures e. g. Rayon/Linen Fabrics requiring this setting usually require steam pressing for heavy cotton, denim etc. Steam/spray/shot of steam Jet clean Without water in tank Dry ironing (160°C Max) Warm (210°C Max) Hot Ironing With water in tank 3 Comfi iron 441375234 Rev 3 31/1/03 11:43 PM Page 5 Components of your iron ¤ < > fi fl / ¤ < > fi fl · , , , · , / , , Filling 1 Make sure that the iron is not plugged in and then set the variable steam control / to the `0' position before filling the iron with water. 2 Lift up the fill cap and fill the water through the filling hole > into the water tank ·, using the beaker provided. In hard water areas the use of distilled or demineralised water is recommended. Never use battery topping up fluid or water containing any substances like starch, or sugar, or defrosted water from a refridgerator. Warning: When filling your iron with tap water always use the beaker provided. A Variable steam/steam boost control Shot of steam button Spray button Filling hole with cap Spray nozzle Soleplate Temperature control dial with indicator Water tank Life long anti-scale (certain models only) Temperature indicator light (red) Auto-shut off light (green) (certain models only) Before use Note: The steam facility should only be used on garments which are suitable for ironing at the 2 and 3 dot settings. When ironing with the steam facility at the 2 dot setting, the steam output should be set at the lower end of the steam range (see variable steam section). If they don't you should follow the fabric guide on page 3, but be sure to test the temperature by ironing the hem of the garment or similar area first. If you turn the control dial down from a hot setting to a cooler setting, wait until the iron temperature has stabilised before you continue ironing. Temperature control Plug in the iron and switch on. Set the temperature control dial B to the temperature required, but don't start ironing immediately. If you wait a few minutes, the iron will stabilise at the required setting. Your Morphy Richards iron is fitted with an indicator light , , which will go on and off while you are ironing. [. . . ] Wait for the temperature indicator light to go out, then unplug the iron and hold it about 6'' (150mm) above the sink in the ironing position. To clean a stainless steel or anodised soleplate (certain models only) To keep the soleplate of your iron clean and free of limescale, we recommend that you use one of the gentle chrome, silver or stainless steel cleaners that are generally available. To clean off melted man-made fibres set the iron at 3 dot position and pass it over a clean piece of cotton which will draw the deposit off the surface. To clean a coated soleplate (certain models only) In the unlikely event of any man-made fibre fusing to the soleplate, set the iron at the 3 dot position and pass it over a clean piece of cotton which will draw the deposit off the surface. [. . . ]