User manual MORPHY RICHARDS IB28034

[. . . ] The time will be displayed but the backlight will be extinguished to conserve battery life. If the optional battery is not installed in case of the AC power failure the clock will start working at 12:00 when power is restored. If the unit is not to be used for a prolonged period, remove the battery to avoid battery leakage. In the interests of environmental safety : dispose of batteries safely. Auto dimmer sensor The unit has an automatic dimmer sensor. [. . . ] Repeatedly press the MODE button until the alarm 1 time appears and flashes. Repeatedly press the SNOOZE button to the set the alarm to sound every day. (SUN MON TUE WED THU FRI SAT appears) or Monday through to Friday (MON TUE WED THU FRI appears) or only Sunday and Saturday (SUN and SAT) appears. Press the DISPLAY button once to the set the alarm mode: buzzer (bell), press (radio) and press again to turn the alarm completely off. Then the ALARM 2 time starts flashing, repeat steps 1-4 to set the ALARM 2 time. If no button is pressed for 15 seconds, the alarm time is stored automatically and returns to the original display. 4 5 Cancelling the alarm 1 To temporarily silence the alarm ( or ), press the SNOOZE button. To cancel the alarm permanently, press the MODE button 3 times, then press the DISPLAY button until the icons disappear. Repeat for alarm 2 if necessary. 2 6 Radio operation · · 1 2 3 4 To obtain maximum FM reception fully extend the wire FM aerial (which is located at the rear of the unit) and alter the direction of the wire for best results. To obtain maximum MW reception rotate the clock radio. Press the POWER / SLEEP button. The radio automatically tunes to the next higher or lower station with a strong signal. Notes If no strong signal is found, press the UP or DOWN buttons to stop tuning. Using the memory You can store up to 20 stations in memory (MW x 10, FM x 10). Within 15 seconds, press buttons 1-5 on the display for the desired memory location. You can also repeatedly press UP or DOWN buttons until the number (0-9 in each band) for the desired memory location appears. Press MEM again to store the station in the memory location. Note: If you do not store the station within 15 seconds, MEMO disappears. · To tune to a stored station, repeatedly press and release MEM until the numbers for the desired memory location and the station appear. For presets 1-5, you can press number key 1-5 to recall the stored station. 7 Last station memory function The frequency of the last station tuned to before switching off the unit will be stored in the memory. When the unit is switched on again, it will receive this station in the respective waveband. When changing the waveband, the last station tuned to in each waveband will also be stored in the memory. Setting the sleep function · · Repeatedly press POWER / SLEEP twice for 2 seconds, until the sleep icon and sleep time 10 appears. To increase the sleep time, repeatedly press the POWER / SLEEP button, each time you press POWER / SLEEP, the sleep time is increased by 10 minutes. (The minimum sleep time you can have is 10 minutes; the maximum sleep time you can have is 90 minutes). Notes: If you don't press any key for 15 seconds, the sleep timer is stored automatically and returns to the original display. [. . . ] The display will still display the time. Warning labels WARNING: to reduce the risk of electric shock, do not expose this appliance to rain or moisture. ATTENTION: To reduce the risk of electric shock, do not remove the cover. The lightning flash with arrowhead symbol within the triangle is a warning sign alerting the user of `dangerous voltage' inside the unit. The exclamation point within the triangle is a warning sign alerting the user of important instructions accompanying the product. 10 Maintenance Do not expose your clock radio to extreme of temperatures. The product should be kept in a warm environment free from dust and damp. Use of detergents may damage the finish. Technical specification AC Power supply Battery back-up Radio : : : : 230V 50Hz 9V DC type 6LR61/PP3 (not included) FM 87. 5MHz - 108MHz MW 522Khz - 1620kHz VENTILATION WARNING The normal ventilation of the product shall not be impeded for intended use. [. . . ]