User manual MORPHY RICHARDS IB28023

[. . . ] Should the fuse in the 13 amp mains plug require changing a 3 amp BS1362 fuse must be fitted. The socket outlet should be installed near the equipment and shall be easily accessible. Switching on and setting the clock time Before you start using your alarm clock, you must start by setting the clock to the correct time. Plug the mains plug into the wall socket and switch on the wall socket. Automatic MSF clock setting 2 The LED clock display will count up from 00 to 59 several times and will then set the time automatically using the MSF signal that it receives from the national physical laboratory at Rugby. Manual clock setting 3 If you wish to set the time manually, press and release the TIME button (2) to change the mode. [. . . ] To exit the alarm setting, press the TIME button once, or wait for 15 seconds the display will revert back to the time. The alarm will automatically turn off after 59 minutes. 4 5 6 7 To advance the day setting by 1, press the HOUR/MSF button once. If an incorrect date is entered after advancing the month, like Apr 31st 2001, the date will be set to the maximum day of that month, which is Apr 30th 2001, automatically. If you do not press any buttons for 15 seconds the clock will return to time mode. Reviewing the day of the week Setting the alarm 2 time 1 1 2 Press the ALARM button twice in time mode. 2 Press and hold the TIME button for 3 seconds in time mode, the current year is displayed. Press the SNOOZE button twice to review the day of the week, the day will appear on the display, dAY1 . . . dAY7 will be displayed which stands for Monday to Sunday respectively. The day of the week cannot be changed but it is already set according to the date. If you do not press any buttons for 15 seconds the clock will return to time mode. Viewing the previous alarm type 1 2 Press the ALARM button to select the setting for alarm 1 or alarm 2. Note : Do not press the SNOOZE button again, otherwise, the type of alarm will be changed. (The alarm mode will also exit if no buttons are pressed for 15 seconds). 3 MSF Signal 1 2 This mode starts when the HOUR/MSF has been pressed in time mode, `-0 0-` displays. If you want to review the current time when receiving MSF signal, press the TIME button. When the MSF signal is detected the two digit counter will count up steadily from 00 to 59, until the clock is synchronised. Note : If the two digit counter is not counting up, then it is not receiving the MSF signal, change the position of the unit for the best reception. When the TIME button is pressed or when a valid MSF signal has been received the clock will return to time mode. The unit will automatically synchronize at 12. 00am and 3. 00am everyday. 3 Reviewing / setting the year 1 2 3 4 Press and hold the TIME button for 3 seconds in time mode, the current year will be displayed. Press the MINUTE button once to change the year in the following sequence: 1999-2000 - . . . If an incorrect date is entered after advancing the year by one, like Feb 29th 2001, the date will be set to the maximum day of that month, which is 28th Feb 2001 automatically. [. . . ] The lightning flash with arrowhead symbol within the triangle is a warning sign alerting the user of `dangerous voltage' inside the unit. The exclamation point within the triangle is a warning sign alerting the user of important instructions accompanying the product. 446/8001/75 Rev 2 Morphy Richards Limited Talbot Road Mexborough South Yorkshire S64 8AJ Your post office will provide a certificate of posting. If you need any further advice, please call our Helpline (UK local rate) on: 08450 777700 (Mon-Fri) Morphy Richards Website: www. morphyrichards. co. uk To prevent fire or shock hazard do not expose this apparatus to dripping and splashing. Imported by : Morphy Richards Ltd, Talbot Road, Mexborough, S64 8AJ Morphy Richards products are intended for household use only. [. . . ]