User manual MORPHY RICHARDS IB26009

[. . . ] Clipper oil is a very thin, natural oil which will not evaporate and will not slow down the blades. Wiring This product is fitted with a 13A (BS1363) plug. Check that the voltage on the rating plate of your clipper corresponds with your house electricity supply which must be A. C. If the socket outlets in your home are not suitable for the plug supplied with this clipper the plug should be removed and the appropriate one fitted. WARNING : The plug removed from the mains lead, if severed, must be destroyed as a plug with bared flexible cord is hazardous if engaged into a live socket outlet. Two Year Guarantee It is in your interest to retain the retailers receipt as proof of purchase. [. . . ] Do not take into a bathroom. Mains lead As a safety precaution and to prolong the life of your appliance, do not wrap the mains lead around the appliance as this will cause damage. Do not operate your clipper with a damaged cord or plug or after the clipper malfunctions or has been damaged in any manner. Ring the helpline number for advice on examination and repair. Morphy Richards products are intended for household use only. Morphy Richards has a policy of continuous improvement in product quality and design. The Company, therefore, reserves the right to change the specification of its models at any time. · While the clipper is running, rapidly move the lever from "close cut" to "longer cut" a couple of times. Doing this each time after you have finished using your clipper will help to keep the blades clear of cut hair. If your clipper stops cutting and this does not help, your cutting blades are dulled. Replace them with new blades. PC26009M UK Rev 1 Instructions & style guide Thank you for buying your new Morphy Richards Clipper set. Please read these instructions carefully before use and keep in a safe place for future reference. Cutting hair with attachments (for medium to long cut) To attach combs, hold comb with teeth up, snap comb attachment firmly to the bottom of the clipper blade. · Key features For the top of the head, you will give a fairly short cut if you use attachment comb 4. With the teeth flat against the head, slowly start trimming from the front to the back. (fig. 4) · Fig. 4 · Top blade Bottom blade Adjustable lever On/off switch Attachment comb 1 -- Leaves hair approx. 12mm in length Outlining · Outlining does not require any attachments. (fig. 5) Make sure the corner edge of the blade is against the hairline. With the outline of the hair as your guide, slowly move the clipper over, around and behind the ears. (fig. 6) For the back of the neck and side burns, hold the clipper upside down and holding it against the skin at the desired length, move downwards. For a flat top, use a flat comb, not the attachment comb. To taper hair down to the neckline, use closer cutting attachment combs. Comb hair and check for uneven spots and outline sideburns and neckline (fig. 9) If a short tapered cut on all sides and back is desired, follow the diagram below: Fig. 9 · · Fig. 5 Comb 4 Comb 3 Comb 2 Comb 1 Comb 1 Comb 2 Comb 3 Comb 4 · · · scissors comb · · · · · oil brush Mains powered 4 cutting guides Includes: brush, scissors, oil, comb, blade guide Adjustable lever Blade cover · · · WARNING: Never use the product to cut wet hair. It is designed to work on dry hair only. Tips · · · · Make sure that the clipper is clean, properly oiled and in perfect working condition. Place a towel around the neck of the person, to prevent hair from falling down inside the collar. Position the person whose hair is to be cut on a chair so that his/her head is at your eye level. [. . . ] To realign the blades, simply match the upper and bottom blades teeth up, point for point. 1. 2mm back from the bottom blade). 1. 2mm Short cuts to crew cuts · Always cut from the back of the neck to the crown, using the longest attachment comb. Holding it flat against the head, slowly move the clipper up through the hair. Using the same technique for the sides, cutting from the bottom to the upper side of the head. [. . . ]