User manual MORPHY RICHARDS ELITE STEAM GENERATOR REV 1

[. . . ] This guarantee is offered as an additional benefit and does not affect your statutory rights as a consumer. · This guarantee is valid in the UK and Ireland only. All Morphy Richards products are individually tested before leaving the factory. In the unlikely event of any appliance proving to be faulty within 28 days of purchase it should be returned to the place of purchase for it to be replaced. If the fault develops after 28 days and within 24 months of original purchase, you should contact the Helpline number quoting Model number and Serial number on the product, or write to Morphy Richards at the address shown. [. . . ] · Do not use the vertical steam feature on clothes that are being worn. · Do not leave the steam generator unattended whilst plugged in or on an ironing board. Never allow the mains lead to over hang the work surface. Special instructions · If your steam generator does not work, check the following points: Has the temperature control been set to the required temperature?(Check by plugging in another appliance). 2 St gen rn42277M rev 1 10/4/03 10:05 PM Page 4 · To prevent damage to the textile being ironed, follow the temperature guide carefully. · When ironing is complete, remove the plug from the socket, empty any remaining water from the tank, and allow to cool before storage. · If you drop or severely knock your steam generator this could cause internal damage even if the outside appears alright. · The temperature of accessible surfaces may be high when the appliance is operating. Electrical requirements Check that the voltage on the rating plate of your appliance corresponds with your house electricity supply which must be A. C. If the socket outlets in your home are not suitable for the plug supplied with this appliance the plug should be removed and the appropriate one fitted. WARNING : The plug removed from the mains lead, if severed, must be destroyed as a plug with a bared flexible cord is hazardous if engaged into a live socket outlet. Should the fuse in the 13 amp plug require changing a 13 amp BS1362 fuse must be fitted. WARNING: THIS APPLIANCE MUST BE EARTHED. Instructions for use Temperature guide Heat setting markings on the adjustable control dial of all Morphy Richards irons match those of the International Textile Care Labelling Code. Symbol (120°C Max) Cool Control knob positions Fabric Do not iron at all Nylon, Acetates e. g. Tricel/Polyester Iron on wrong side if moisture required use damp cloth (Not Acetate) Wool, Polyester mixtures e. g. Rayon/Linen Fabrics requiring this setting usually require steam pressing for heavy cotton, denim etc. (160°C Max) Warm (210°C Max) Hot Ironing Steaming 3 St gen rn42277M rev 1 10/4/03 10:05 PM Page 5 Components of your iron / fi Location Locate the steam generator horizontally on the iron rest plate of your ironing board (if large enough) or on a heat resistant stand at the same height of your ironing board or below it. Always ensure the generator is on a firm surface when ironing. ¤ > Before use fl < · Remove any protective sticker from the soleplate and the cabinet, if any. When ironing with the steam facility at the 1 dot setting, the steam output should be set at the lower end of the steam range. If they don't you should follow the fabric guide on page 3, but be sure to test the temperature by ironing the hem of the garment or similar area first. If you turn the control dial down from a hot setting to a cooler setting, wait until the iron temperature has stabilised before you continue ironing. , , ,  Filling Iron unit / Steam button ¤ Temperature control dial < Sole plate > Temperature indicator light fi Supply cord from base unit Base unit fl Anti-scale cartridge Water tank · Power cord , Power switch , , -Standby mode indicator (red) -Power indicator (green) -Sleep mode indicator (green/red) Replace anti-scale medium indicator  Steam level indicators 1 Place the steam generator on a stable ironing board or table, with the iron resting on its stand. B B 4 St gen rn42277M rev 1 10/4/03 10:05 PM Page 6 4 Fill the tank upto the `fill to here' line with clean tap water. Never use battery topping up fluid or water containing any substances like starch or sugar, or defrosted water from a refridgerator. 5 Re-install the anti-scale cartridge and replace the water tank on the base unit. C Re-filling 1 When the water level reaches a low level, the pump begins to emit a clicking noise. [. . . ] This feature is especially useful for removing creases from hanging clothes, curtains, wall hangings, etc. Unplug the generator and leave the iron to cool off for 15 minutes minimum. The iron and boiler can now be stored together. Maintenance To clean a stainless steel soleplate To keep the soleplate of your iron clean and free of limescale, we recommend that you use one of the gentle chrome, silver or stainless steel cleaners that are generally available. To clean off melted man-made fibres set the iron at 3 dot position and pass it over a clean piece of cotton which will draw the deposit off the surface. To clean the exterior Allow the steam generator to cool and wipe over with a damp cloth and mild detergent, then wipe with a dry cloth. H Emptying and storing When you have finished ironing, unplug your iron. [. . . ]