User manual MORPHY RICHARDS CORDLESS HAND BLENDER REV 1

[. . . ] · Teach children to be aware of dangers in the kitchen, warn them of the dangers of reaching up to areas where they cannot see properly or should not be reaching. Location · Do not use outdoors. Charger lead · The charger lead should reach without straining the connections. · Do not let the charger lead hang over the edge of a worktop where a child could reach it. · Do not let the charger lead run across a cooker or toaster or other hot areas which might damage the cable. Other safety considerations · Do not operate any appliance with a damaged charger lead or after the appliance malfunctions or has been damaged in any manner. Do not use accessories not recommended by the manufacturer as there is the danger of fire, electric shock or personal injury. [. . . ] WARNING: Never use your appliance in a hot saucepan transfer to a bowl, allow to cool before blending. Allow to cool down for a minimum of 5 minutes before further use. To disassemble hand blender 1 To remove the blender leg, hold the blender in a position so that you cannot press the operating button. D WARNING: When the blender is not in use, fit the blade cover to the leg for safety. D C E 5 48965 Rev 1 13/4/04 3:47 PM Page 6 Hints for blending · The blender is perfectly suited for preparing dips, sauces, soups, mayonnaise, milkshakes and baby food. The blender can be used to purée cooked vegetables, tinned tomatoes and any soft or pre-cooked food etc. It is ideal to turn a cooked broth or stew into a smooth soup and to prepare baby food. You may need to add a little water to cooked vegetables when blending to encourage a puree to form. For milkshakes, cut soft fruit or bananas in 1. 5cm cube size pieces for easy blending, add milk and icecream a little at a time during blending. If food has been cooked in a saucepan transfer to a cooler bowl, this will protect the leg from heat distortion. Blending results will be better in the beaker provided as this allows control of the food being blended. Battery removal and disposal To remove the Ni-Cd battery for replacement or disposal. 1 Remove the 2 screws from the end of the battery cap, using a small phillips screwdriver and lift off the cap. G 2 Remove the connector from the end of the battery and pull out the battery. H · Replace with an approved battery pack, contact Morphy Richards replacement parts 0870 167 6643. 3 Replace the battery, (terminal to be in position shown) connect the terminal, replace battery cover ensuring it is correctly located and replace the 2 screws. IMPORTANT: The battery must be removed before the product is disposed of. The battery is to be disposed of safely, it must not be incinerated or composted. Contact your local authority for advice on disposal. · · · · Blender rest position Whilst not blending temporarily, lay the blender down on the work top as shown. F G F H battery terminal in lower left hand corner 6 48965 Rev 1 13/4/04 3:47 PM Page 7 Wall mounting The charging stand can be wall mounted or free standing. To wall mount find a suitable position on the wall away from concealed pipes and electricity cables. Use the stand with blender in place to determine the position most suitable, mark a line on the wall across the top of the charger stand. From this line mark a horizontal line 15mm below, now mark 2 holes 40mm apart. I Using wall plugs and screws provided, fix so screw heads are 5mm from the surface. Hang the charger base and adjust the depth position of the screws if required to improve the fit. Tips for blending When processing foods with strong colour (eg. [. . . ] This guarantee is offered as an additional benefit and does not affect your statutory rights as a consumer. · This guarantee is valid in the UK and Ireland only. All Morphy Richards products are individually tested before leaving the factory. In the unlikely event of any appliance proving to be faulty within 28 days of purchase it should be returned to the place of purchase for it to be replaced. If the fault develops after 28 days and within 24 months of original purchase, you should contact the Helpline number quoting Model number and Serial number on the product, or write to Morphy Richards at the address shown. [. . . ]