User manual MORPHY RICHARDS BIG POD BAGLESS VACUUM CLEANER REV 2

[. . . ] If you cut off the plug and let go of the cable it will rewind into the machine. Therefore you must pull out a length of cable and secure it before cutting off the plug and refitting a new one. WARNING: The plug removed from the mains lead, if severed, must be destroyed as a plug with bared flexible cord is hazardous if engaged into a live socket outlet. Should the fuse in the 13 amp plug require replacement, a BS1362 13 amp fuse must be fitted. Mains lead · Do not allow the mains lead to become strained or run this appliance over it. [. . . ] 6 Start vacuuming Do not use the cleaner in an upright position. B C Release button 4 73195 rev2 24/10/05 11:55 AM Page 5 After use 1 Switch off the vacuum cleaner. WARNING: When using the cable rewind, always hold the plug as the cable will rewind quickly. Emptying the pod WARNING: Never operate the cleaner without the dust pod filter assembly Ï or motor protection filter fitted. 3 Remove the dust pod fl from the cleaner by pushing the release latch /D. 5 Raise the filter assembly Í handle then lift out the filter assembly from the dust pod flE. 8 Use the small brush Ì provided (located on filter assembly) to remove any fluff from the outside of the mesh filter G. 9 Rotate the mesh filter Î clockwise to release the mesh filter and pleated filter Ï assembly from the filter holder G. 10 Rotate and flick the pleated filter inside the mesh filter to shake loose the dust. E 11 Lift out the pleated filter Ï then empty out the dust from the mesh filter Î into the bin E 12Re-assemble filter assembly by placing the pleated filter inside the mesh filter then place the filter holder on top in the correct position. Rotate the mesh filter assembly anti-clockwise to lock the assembly together H. 13 Place the filter assembly back inside the dust pod making sure the filter assembly is placed level and that the filter holder seal is seated neatly. 14 Re-attach the dust pod to the cleaner by hooking the bottom of the dust pod in first, then closing the pod until it clicks and the pod release catch /. is fully down and secured I. E D F 5 73195 rev2 24/10/05 11:55 AM Page 6 If there is resistance when you re-fit the pod onto the cleaner, remove and carefully reseat the filter assembly back into the pod, ensuring the filter assembly seal is located fully and neatly. G Washing the pleated filter For total cleaning of the pleated filter it should be washed with warm water with no detergents. This allows continued use of the cleaner whilst the other filter is drying. IMPORTANT: The filter must be completely dry before re-fitting. 73195 rev2 24/10/05 11:55 AM Page 7 Motor protection filter This cleaner is fitted with a motor protection filter. IMPORTANT: NEVER USE THE VACUUM CLEANER WITHOUT THIS IN PLACE. To clean the motor protection filter 1 Remove the filter from the filter grille J. 3 Put the filter back into the filter grille and reassemble. Storage position The vacuum cleaner can be stored in an upright position. Slide the storage hook , on the floor nozzle into the slot on the base of the product and the tubes, hose and floor nozzle are held securely K. G J I K 6 73195 rev2 24/10/05 11:55 AM Page 8 Exhaust filter This filter should be replaced every 12 months or sooner if required. Remove the exhaust filter grille by pulling the locking tabs towards you L. IMPORTANT · Always disconnect the cleaner from the mains when checking filters. · All filters should be checked regularly for signs of damage, preferably after each cleaning task. [. . . ] You may be asked to return a copy of proof of. purchase Subject to the exclusions set out below (1-5), the faulty appliance will then be repaired or replaced and dispatched usually within seven working days of receipt. If you suspect a fault, follow the simple checks detailed below before returning the appliance or calling the helpline. · Check the plug is firmly in the socket and the supply is switched on. · Make sure the socket is working by trying another appliance. If for any reason this item is replaced during the two-year guarantee period, the guarantee on the new item will be calculated from original purchase date. [. . . ]