User manual MORPHY RICHARDS ADVANCED FINISH IRON

[. . . ] When placing the iron on its heel, ensure that the surface on which the heel is placed is stable. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience or knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. · · · Other safety considerations Use the iron only for its intended use. Always disconnect the iron from the electrical socket when filling with water or emptying, and when not in use. [. . . ] Note: The steam facility should only be used on garments which are suitable for ironing at the 2 and 3-dot settings (see `Temperature guide' on page 3). If they don't, you should follow the fabric guide on page 3, but be sure to test the temperature by ironing the hem of the garment or similar discreet area first. If you turn the control dial down from a hot setting to a cooler setting, wait until the iron temperature has stabilised before you continue ironing. Delicate fabrics such as silk, wool, velour, etc, are best ironed with an ironing cloth to prevent shine marks. 4 UK Helpline 0844 871 0953 Replacement Parts 0844 873 0719 Ireland Helpline 1800 409 119 RN40743 MUK Rev6:40715 rev3 27/03/2009 14:18 Page 5 FILLING A 1 Make sure that the iron is not plugged in, then set the steam dial < to `0' position before filling the iron with water. Lift up the filler cap > and fill the water through the filling hole into the water tank , , , using the beaker provided  A. IN HARD WATER AREAS, THE USE OF DISTILLED OR DEMINERALISED WATER IS RECOMMENDED. WARNING: Never use battery topping up fluid or water containing any substances like starch, or sugar, or defrosted water from a refrigerator. WARNING: When filling your iron with tap water, always use the beaker provided. Never fill directly under the tap. · 2 Your Morphy Richards iron is fitted with a temperature indicator light , which will go on and off whilst you are ironing. This is perfectly normal as it shows that the iron is maintaining the heat setting you have chosen. It is always a good idea to begin with cool fabrics and work up to higher settings. An iron heats up quicker than it cools down so you will save time and energy. A · FEATURES OF YOUR IRON Dry ironing You can use your iron as a dry iron only. Make sure the variable steam control < is set to the `0' symbol. The spray feature may be used, provided there is water in the tank (see `Filling' section). You do not need to put any water in the tank when dry ironing only. TEMPERATURE CONTROL B B Water Spray C Press the spray button / and aim the spray of water at stubborn creases. You can do this whilst dry ironing providing there is water in the tank. When using the water spray it may be necessary to push the button a few times to get the spray pump primed. C / 1 Plug in the iron and switch on. Set the temperature control dial to the temperature required B, but don't start ironing immediately. If you wait a few minutes, the iron will stabilise at the required setting. 2 For details of other Morphy Richards products, please see our website: 5 RN40743 MUK Rev6:40715 rev3 27/03/2009 14:18 Page 6 D Steam off Variable steam Fill the iron with water as described in `Filling', page 4, and insert the plug into the electrical socket. The steam output can be varied from low to high by turning the variable steam control D. When using the iron at the bottom of the steam range, the steam output should be adjusted to the low setting. The steam facility should only be used on garments which are suitable for ironing at 2, 3-dot and MAX setting. No drip system Your iron is fitted with a no drip system which is designed to prevent water escaping from the soleplate fl when the iron is too cold. [. . . ] This guarantee is offered as an additional benefit and does not affect your statutory rights as a consumer. This guarantee is valid in the UK and Ireland only. 5 6 7 · EXCLUSIONS Morphy Richards shall not be liable to replace or repair the goods under the terms of the guarantee where: 1 The fault has been caused or is attributable to accidental use, misuse, negligent use or used contrary to the manufacturer's recommendations or where the fault has been caused by power surges or damage caused in transit. The appliance has been used on a voltage supply other than that stamped on the products. Repairs have been attempted by persons other than our service staff (or authorised dealer). [. . . ]