User manual MORPHY RICHARDS 73285 BAGLESS UPRIGHT VACUUM CLEANER

[. . . ] If the cleaner is knocked over, switch off before attempting to upright. Never pick the cleaner up by the floor nozzle when connected to the mains, use the carrying handle. · · · · · · Children · Children do not understand the dangers associated with operating electrical appliances. Children should be supervised to ensure that they do not play with the appliance, or stumble over the power cord. Location · · Do not use or keep this product outside. ovens or heating appliances. · Mains lead · Do not allow the mains lead to become strained or run this appliance over it. [. . . ] Set the floor nozzle height adjustment dial · to the desired position. Release the mains cable by revolving the quick release cleat Ë half-a-turn and extend the cable fully. Step on the upright release pedal Ì to release the vacuum to the desired position. IMPORTANT: To prevent damage to carpets: · Never leave the cleaner switched on in one place for an extended period. Never have the brushes set too low such that the cleaner is hard to push. Never lean on the product. 3 If additional length is required, remove the telescopic tube from the cleaner, connect it to the handle, and add the desired accessory to the end of the tube G. IMPORTANT: When using the hose and tools, locate the hose into the hose hook Ï on the main unit. IMPORTANT: Turning the cleaner sideways helps prevent the cleaner being pulled along by the stretched hose. F 3 4 · 4 5 · 6 Using & cleaning the turbo nozzle (certain models only) Attach the Turbo nozzle to either the handle or the telescopic tube as described previously. If they are tightly wound around the brush, carefully snip the fibres with scissors, being careful not to damage the brush bar, pull away from the brush bar and dispose. · · Using the attachments 1 Follow steps 1-4 of the `Using on carpets' section, but set the floor nozzle height adjustment dial to the tools setting. Attach the accessories , , , to the handle, removing the handle from the telescopic tube, then firmly push on the desired accessory F: Turbo nozzle , (certain models only) is ideal for pet hair removal from stairs and upholstery. Crevice tool for awkward places, corners and behind radiators etc. SAFETY CUT-OUT If the cleaner overheats, a motor protection thermostat will automatically switch the motor off. If this happens, switch the cleaner off, unplug from the power supply and leave the cleaner to cool for at least 60 minutes. Check the airways for blockages, empty the dust canister and clean the filters before restarting. 2 G www. goblin-vacuums. com 5 VC73285MUK Rev2:VC73285MUK Rev2 19/01/2010 09:40 Page 6 H Ê EMPTYING THE DUST CANISTER Empty the dust canister regularly even if it does not look full, this will maintain the performance. IMPORTANT: Always empty the dust canister and clean the filter and mesh following prolonged use. Clean the filter and mesh screen every time the dust canister is emptied. I 1 2 Turn the cleaner off and unplug from the mains switch. Press the dust canister release button Ê and pull the canister away from the main body H. This opens the door at the base of the canister for the contents to be emptied-out I. 1 2 Motor protection filter The motor protection filter Ò is located underneath the dust canister in the air-inlet pipe. 3 Replace the filter. Ô 3 4 J REMOVING AND CLEANING THE FILTERS HEPA filter IMPORTANT: After every empty, clean the dust canister filter fl. Exhaust filter The exhaust filter Ú is located below the dust canister compartment. Remove the exhaust filter by twisting the motor protection filter cover Û and lifting it away O. Rotate until it clicks into place. K 1 2 Empty the dust canister . Remove the dust canister lid fi by turning it counter-clockwise, then lifting off J. Insert the height adjustment knob, carefully turning it until it locates into the mating keyway on the cam. [. . . ] Please quote the following information if the product develops a fault. All Goblin products are individually tested before leaving the factory. In the unlikely event of any appliance proving to be faulty within 28 days of purchase, it should be returned to the place of purchase for it to be replaced. If, for any reason, this item is replaced during the 1 year guarantee period, the guarantee on the new item will be calculated from original purchase date. Therefore it is vital to retain your original till receipt or invoice to indicate the date of initial purchase. [. . . ]