User manual MORPHY RICHARDS 42303 STEAM GENERATOR

[. . . ] If your iron is placed for a few moments on the iron rest plate, this plate may reach very high temperatures. In this instance, do not touch the iron soleplate or the iron rest plate until the iron and the iron rest have cooled down. WARNING: To protect against the risk of electric shock, do not immerse the appliance in water or in any other liquid. Do not leave the steam generator unattended whilst plugged in or on an ironing board. [. . . ] 2 Turn the temperature dial > on the iron in a clockwise direction, select dot-1, dot-2 or dot-3 according to the recommendation of the garment label. The iron's temperature indicator light ¤ goes off when the required temperature is reached. Depress the steam button / for 1 minute to clear the system of air (first time use only). Note: If you press the steam button before the steam generator reaches its required temperature, a warning double beep will sound. The appliance is ready to use. FILLING B 1 Place the steam generator on a stable ironing board or table, with the iron resting on its stand. Release the detachable water tank by operating the tank release knob , , . IN HARD WATER AREAS, THE USE OF DISTILLED OR DEMINERALISED WATER IS RECOMMENDED. Never use battery topping up fluid or water containing any substances like starch or sugar, or defrosted water from a refrigerator. 5 Re-position the water tank on the base unit and push securely into place. Always pour out any remaining water after use. 2 LOCATION Locate the steam generator horizontally on the rest plate of your ironing board (if large enough) or on a heat resistant stand at the same height as your ironing board or below it. WARNING: Do not use the product on a surface which could be damaged by heat or steam such as a worktop or a polished wood surface. If in doubt, contact Morphy Richards. 3 4 BEFORE USE Remove any protective sticker from the soleplate and the base unit, if any. Slide out the water tank · and fill (see filling instructions). When ironing with the iron temperature set at 2-dot setting, the steam output should be set at the lower end of the steam range (on certain models only). If they don't, you should follow the fabric guide on page 3, but be sure to test the temperature by ironing the hem of the garment or similar area first. 6 Re-filling `in use' 1 The low water indicator light Ê will flash and a beep sound will be heard. Ironing can continue for a short period, then the generator will shut down until the tank is refilled. Slide out the water tank and fill (see filling instructions). 3 4 2 5 3 6 For details of other Morphy Replacement Parts 0870 our website: UK Helpline 0870 060 2614Richards products, please see157 6645 Ireland Helpline 1800 409119 5 RN42288MUK Rev7:RN42288MUK Rev7 04/11/2009 10:28 Page 6 7 8 Press the steam button / for steam ironing. Depress the power switch Á to turn off the base unit when ironing is complete. 4 The temperature indicator light ¤ glows on the iron, indicating that it is switched on. When the required temperature is reached, the temperature indicator light on the iron goes off. It is always a good idea to begin with `cool' fabrics and work up to higher settings. An iron heats up quicker than it cools down so you'll save time and electricity. 5 MODELS WITH SPRAY FEATURE Certain models are fitted with a spray feature. [. . . ] Please refer to the one year guarantee for more information. YOUR ONE YEAR GUARANTEE It is important to retain the retailer's receipt as proof of purchase. Please quote the following information if the product develops a fault. All Morphy Richards products are individually tested before leaving the factory. In the unlikely event of any appliance proving to be faulty within 28 days of purchase, it should be returned to the place of purchase for it to be replaced. EXCLUSIONS Morphy Richards shall not be liable to replace or repair the goods under the terms of the guarantee where: 1 The fault has been caused or is attributable to accidental use, misuse, negligent use or used contrary to the manufacturer's recommendations or where the fault has been caused by power surges or damage caused in transit. [. . . ]