User manual MORPHY RICHARDS 40850 COMFIGRIP IRON

[. . . ] WARNING: To protect against the risk of electric shock, do not put the appliance in water or in any other liquid. The socket should always be off before plugging or unplugging from the socket. Never yank the cord to disconnect from the socket, instead, grasp the plug and pull to disconnect. The iron must not be left unattended while it is connected to the supply mains. [. . . ] Delicate fabrics such as silk, wool, velour, etc, are best ironed with an ironing cloth to prevent shine marks. 4 UK Helpline 0844 871 0953 Replacement Parts 0844 873 0719 Ireland Helpline 1800 409 119 RN40850 MUK Rev2:RN40850 MUK Rev2 19/03/2010 09:37 Page 5 FILLING A 1 Make sure that the iron is not plugged in, then set the steam dial < to `O' position E before filling the iron with water. Lift the filler cap > until it locks and holds in the open position. Fill the water through the filling hole into the water tank , , using the beaker provided A. The iron is fitted with a clear view water tank, so you can easily see the water level when filling. IN HARD WATER AREAS, THE USE OF DISTILLED OR DEMINERALISED WATER IS RECOMMENDED. Never use battery topping up fluid or water containing any substances like starch, or sugar, or defrosted water from a refrigerator. WARNING: When filling your iron with tap water, always use the beaker provided. Never fill directly under the tap. 2 Set the temperature dial to the temperature required C, but don't start ironing immediately. If you wait a few minutes, the iron will stabilise at the required setting. Your Morphy Richards iron is fitted with a temperature indicator light · which will switch on and off whilst you are ironing. This is perfectly normal as it shows that the iron is maintaining the heat setting you have chosen. It is always a good idea to begin with cool fabrics and work up to higher settings. An iron heats up quicker than it cools down so you will save time and energy. A 2 · · B FEATURES OF YOUR IRON Dry ironing You can use your iron as a dry iron only. Make sure the variable steam control < is set to the `O' symbol E. The spray feature may be used, provided there is water in the tank (see `Filling' section). You do not need to put any water in the tank when dry ironing only. MAX level mark Water Spray D Press the spray button / and aim the spray of water at stubborn creases. You can do this whilst dry ironing providing there is water in the tank. When using the water spray it may be necessary to push the button a few times to get the spray pump primed. TEMPERATURE CONTROL C C D / O ON WO 1 Plug in the iron and switch on the power at the mains socket. For details of other Morphy Richards products, please see our website: M SI A X MIN K L N YL L C O TT ON LINEN 5 RN40850 MUK Rev2:RN40850 MUK Rev2 19/03/2010 09:37 Page 6 E Variable steam Fill the iron with water as described in `Filling', page 5, and insert the plug into the electrical socket. Off / No steam Vertical steam Hold the iron in a vertical position between 1cm and 2cm away from the item G. Press the steam boost button ¤, this will create vertical steam. This feature is especially useful for removing creases from hanging clothes, curtains, wall hangings, etc. Note; For optimum steam quality, do not operate the shot more than three times in succession. The steam output can be varied from low to high by moving the variable steam control. When using the iron at the bottom of the steam range, the steam output should be adjusted to the low setting. [. . . ] Please refer to the one year guarantee for more information. YOUR ONE YEAR GUARANTEE It is important to retain the retailer's receipt as proof of purchase. Please quote the following information if the product develops a fault. All Morphy Richards products are individually tested before leaving the factory. In the unlikely event of any appliance proving to be faulty within 28 days of purchase, it should be returned to the place of purchase for it to be replaced. EXCLUSIONS Morphy Richards shall not be liable to replace or repair the goods under the terms of the guarantee where: 1 The fault has been caused or is attributable to accidental use, misuse, negligent use or used contrary to the manufacturer's recommendations or where the fault has been caused by power surges or damage caused in transit. [. . . ]