User manual MIO C210

[. . . ] 14 Right-Side Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Top Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Bottom Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 2 Basic Skills . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 2. 1 2. 2 2. 3 Turning Your Device On and Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Be sure that you place the device in an appropriate place, so as not to obstruct the driver's view, or deployment of airbags. Do not mount where the driver's field of vision is blocked. Do not place unsecured on the dashboard. Do not mount in front of airbag panels. Do not mount in front of an airbag field of deployment. 6 1 Getting Started This chapter tells you how to install the batteries and introduces the components of your device. 1. 1 Installing the Batteries NOTE: For using the device in car, you can also connect the device to the in-car power cable. Prepare four "AA" batteries of the same type and manufacturer. Place the batteries with their terminals corresponding to the (+) and (-) indications. Slide the back cover into place and make sure it clicks into position. 7 CAUTION: Immediately replace the batteries whenever the batteries are low. It is important that the batteries have power for the device operation even though power can be supplied to your device through the in-car power cable or USB cable. When replacing the batteries, use the batteries of the same type and manufacturer. When not using the battery for a long period (more than one month), remove the batteries to prevent damage from battery corrosion. In case the battery leaks, clean the liquid and install new batteries. NOTE: After replacing the batteries, you need to press the power button for five seconds to turn on your device. (See the following section for more information. ) Depending on the characteristics of different battery types, the length of operation time might differ from one to the other. Check the regulations of your local government for proper battery disposal. 1. 2 Performing the Initial Start Up 1. Make sure that power is supplied to your device either by batteries or by the in-car power cable. For the initial start up, press the power button for five seconds to turn on your device. NOTE: For normal operation, briefly press the power button to turn on and off your dvice. 3. Tap the arrow button to select the time zone, date and time for your system. You can now start using your device. 9 1. 3 Using Your Device in a Vehicle A car holder and an in-car power cable are supplied with your device. Using the Car Holder CAUTION: Select an appropriate location for the car holder. Never place the holder where the driver's field of vision is blocked. If the car's windshield has window tint, it is recommended that you use a car antenna (optional) to route the antenna to the top of the car through the window. (For a car with the anti-jam design, the window will automatically leave space. ) Use the car holder to fix the device near the windshield. Connecting the In-Car Power Cable The in-car power cable supplies power to your device when you are using the device in a car. CAUTION: To protect your device against sudden surges in current, connect the in-car power cable only after the car engine has been started. If you are using the rechargeable batteries, connecting to the in-car power cannot provide power to your batteries. 1. Connect the one end of the in-car power cable to the cigarette lighter in the car. When your device has power, the power indicator glows green. 10 11 1. 4 Understanding Hardware Features NOTE: Depending upon the specific model purchased, the color of your device may not exactly match the device shown in this manual. Front Components Ref Component Touch Screen Description Displays the output of your device. [. . . ] Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate the equipment. Please note: The use of a non-shielded interface cable with this equipment is prohibited. Canada Canadian Department Of Communications Radio Interference Regulations Class B Compliance Notice This Class B digital apparatus meets all requirements of the Canada Interference-Causing equipment regulations. Cet appareil numérique de Classe B respecte toutes les exigences du Règlement Canadien sur le matériel brouileur. European Notice Products with the CE marking comply with Radio & Telecommunication Terminal Equipment Directive (R&TTE) (1999/5/EEC), the Electromagnetic Compatibility Directive (89/336/EEC) and the Low Voltage Directive (73/23/EEC) ­ as amended by Directive 93/68/ECC - issued by the Commission of the European Community. [. . . ]