User manual MINOLTA SR-T 200

[. . . ] The included medium-format film holder uses antinewton glass and includes masks for 6x4. 5, 6x6, 6x7, 6x9. · 12-bit AD converter, so fine detail is captured with a dynamic range. This manual has been designed to help you understand the operation of your scanner. To realize all the benefits of your scanner, please read this manual and the accompanying software manual thoroughly. [. . . ] Connect the other end of the SCSI cable to the SCSI port on the computer or on the last SCSI device in the chain. 3. Flip the dip switch marked 1 up to turn the terminator on. · Dip switches 2 through 4 are inactive. Their position will not affect the scanner operation. 9 Continued on following page. CONNECTING TO THE COMPUTER 4. · Place the scanner on a stable surface. 14 LOADING 35MM FILM HOLDERS SLIDE MOUNT HOLDER SH-M1 · The slide mount holder can hold up to 4 mounted slides (35mm or APS). · Slide mounts must be thicker than 1mm and thinner than 2mm to fit properly into the holder. · Results of scanning glass-mounted slides can be unpredictable. · Blow dust off the slide before placing it into the film holder. 1. Position the slide mount holder so the white arrow is on the top-left side, then open the slide mount. · Open the slide holder by pushing up on the two tabs from underneath. 2. Place the slides within the indentations, making sure they lie flat. · Insert the slides emulsion side down. 3. Press the cover firmly closed until it clicks. 15 35MM FILM HOLDER FH-M1 Use the FH-M1 for 35mm negatives and unmounted 35mm slide film. · The 35mm Film Holder FH-M1 can hold film strips up to 6 frames long. · Blow dust off the film before placing it into the film holder. 1. · With larger film formats, the corners of the frame may not fit in the scanning area when the carrier is rotated. 3. Turn the holding screw clockwise to secure it. 22 INSERTING THE HOLDER INTO THE SCANNER 1. Turn on your computer, then launch the Dimâge Scan Multi II software. · The green indicator lamp will blink slowly while the scanner is setting up. 2. Insert the holder into the scanner in the direction indicated by the white arrow on top of the holder. · Do not insert the holder at an angle. 3. Gently push the holder into the scanner until the raised insertion mark is aligned with the film-slot door. · The film holder will be automatically guided in past the mark. · If the holder is not loaded correctly, then eject and reinsert it. EJECTING 1. Press the eject button on the front of the scanner. · The holder will automatically eject partway, then stop. 2. Remove the holder. · Wait for the Indicator lamp to turn off before removing the holder. · The holder should pull out easily. 23 APS ADAPTER AD-100 (SOLD SEPARATELY) · The APS Adapter AD-100 (optional accessory) is required to scan APS film in the cassette with the Dimâge Scan Multi II. Only processed film with the VEI set to the APS Adapter AD-100. can be inserted into APS ADAPTER ­ NAMES OF PARTS Film-chamber release Film-chamber door Scanner contacts* * Do not touch 24 LOADING THE CASSETTE 1. Slide the film-chamber release as shown. · The film chamber door will open. 2. Insert the film cassette into the film chamber with the VEI on top. · Only load cassettes displaying the mark. 3. [. . . ] There should be no uncovered space between the film and the mask. Pages 18 -21. The indicator lamp glows red. If using a film holder: The accessory panel is open. Page 26. 31 Continued on following page. TROUBLESHOOTING Symptom The indicator lamp is red and blinks rapidly or The scanned image is black. Cause/Action 1. If the cover was closed, the fluorescent lamp works, and the red lamp continues to blink rapidly, there is a hardware problem. Turn off and unplug the scanner, then call a Minolta Service Facility. Reference Page 28. The scanned image colour is strange. Check that there is no dust on the film or film holder. [. . . ]