User manual MINOLTA MAGICOLOR 3300

[. . . ] magicolor 3300 User's Guide ® 1800712-001A Trademarks The following are registered trademarks of MINOLTA-QMS, Inc. : QMS, the MINOLTAQMS logo, Crown, CrownNet, and magicolor. Other product names mentioned in this guide may also be trademarks or registered trademarks of their respective owner s. Proprietary Statement The digitally encoded software included with your printer is Copyrighted © 2003 by MINOLTA-QMS, Inc. This software may not be reproduced, modified, displayed, transferred, or copied in any form or in any manner or on any media, in whole or in part, without the express written permission of MINOLTA-QMS, Inc. Copyright Notice This guide is Copyrighted © 2003 by MINOLTA-QMS, Inc. , One Magnum Pass, Mobile, AL 36618. This document may not be copied, in whole or part, nor transferred to any other media or language, without written permission of MINOLTA-QMS, Inc. Notice MINOLTA-QMS, Inc. [. . . ] The maximum size of PDF files which may be printed on the magicolor 3300 is determined by the amount of installed memory. Direct printing of complex or large PDF files may require additional memory (RAM) and/or a hard disk. We recommend a hard disk for optimum performance when printing large PDF files. Refer to the CrownBooks on how to adjust the memory clients. Printing Preformatted Files Using CrownView Your printer also provides a utility via the CrownView web page for printing PDF files directly from the host using the browser. Users will be presented with a Browse button that, when selected, will enable a file chooser on the host. Users then select the file that they want to send to the printer, and the file is transferred and printed. Troubleshooting PDF Direct Printing from CrownView If you are having problems printing large PDF files using direct printing or CrownView from a PC or UNIX, increase the PS Wait Timeout. Printing large PDF files from your web browser with the MINOLTA-QMS CrownView feature may fail without any indication of an error. The job will appear to start normally, but then flush without printing. To correct the problem, increase the amount of time allowed before the PS Wait Timer expires. Doubling the value to 60 seconds in the Administration/Communications/ Timeouts/PS Wait Timeout menu should correct most problems, or the value can be set to 0 seconds, which effectively makes the timeout period infinite. Direct PDF File Printing 83 Preventing Media Jams Make sure that. . . You have the correct media type selected if you're printing on envelopes, glossy stock (set as Thick 2 or Thick 3), labels, thick stock, or transparencies. You always adjust the media width regulation guides in the media tray after inserting the media (a guide that is not properly adjusted can cause poor print quality, paper jams, or printer damage). If you're printing simplex pages, make sure you load the media printing side down in the multipurpose tray, but printing side up in the other trays. Often, an arrow on the media package label indicates the printing side of the media. If you can't determine which side of the media to print on, remove the media from the tray, rotate the stack a half-turn, turn the stack over, and then place it back in the tray. Double feeding (remove the media and fan the sheets--they may be sticking together). Loading more than one type/size/weight of media in a tray at the same time. Allowing the output tray to overfill (the face-down output tray has a 250-sheet capacity--jamming may occur if you allow media to accumulate more than 250 sheets at a time). This causes static electricity. 84 Preventing Media Jams Automatic Jam Recovery The printer provides automatic jam recovery (when enabled through the Administration/Engine/Page Recovery menu). After you remove any jammed media, printing automatically resumes from the page the printer stopped at when the jam occurred. For automatic jam recovery to work, it is necessary to leave the printer turned on when you remove the jammed media. After the jam is cleared, open and close the front door before printing. [. . . ] Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. A shielded cable is required to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. Attention Any modifications or changes to this product not expressly approved in writing by the manufacturer responsible for compliance to Federal Regulations could void the user's authority to operate this product within the Laws and Regulations of the Federal Communications Commission. Canadian Users Notice This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. CE Marking (Declation of Conformity) This product complies with the following EU directives: 89/336/EEC, 73/23/ EEC, and 93/68/EEC directives. This declaration is valid for the areas of the European Union (EU) only. [. . . ]