User manual MINOLTA MAGICOLOR 2210

[. . . ] magicolor 2200 User's Guide ® 1800616-001B Trademarks The following are registered trademarks of MINOLTA-QMS, Inc. : QMS, the MINOLTA-QMS logo, and magicolor. Other product names mentioned in this manual may also be trademarks or registered trademarks of their respective owners. Proprietary Statement The digitally encoded software included with your printer is Copyrighted © 2000 by MINOLTAQMS, Inc. This software may not be reproduced, modified, displayed, transferred, or copied in any form or in any manner or on any media, in whole or in part, without the express written permission of MINOLTA-QMS, Inc. Copyright Notice This manual is Copyrighted © 2000 by MINOLTA-QMS, Inc. , One Magnum Pass, Mobile, AL 36618. This document may not be copied, in whole or part, nor transferred to any other media or language, without written permission of MINOLTA-QMS, Inc. Manual Notice MINOLTA-QMS, Inc. [. . . ] If necessary, replace it. There are toner smudges on the back side of the page (whether or not it has been duplexed). The paper transport rollers may be dirty. The media path is dirty with toner. Clean the paper transport, pressure, and fuser oil rollers. Print several blank sheets and the excess toner should disappear. The fuser oil roller is dirty or Remove the fuser oil roller and check the roller surface for worn. Replace the fuser unit. Image defects in same place on every page. The transfer belt is defective. If necessary, replace it. ABCDE ABCDE ABCDE ABCDE 80 Solving Problems with Printing Quality Symptom Abnormal areas (white or black) appear in a regular pattern. Cause Width of abnormal area: 1. 25" (31. 75 mm) The toner cartridge is damaged. Width of abnormal area: 3" (76. 2 mm) The transfer belt is damaged. Width of abnormal area: 3. 25" (82. 55 mm) The OPC drum cartridge is damaged. Width of abnormal area: 8" (203. 2 mm) The transfer belt is damaged. Solution Remove the toner cartridge with the color causing the abnormal image. Replace it with a new toner cartridge. Replace the transfer belt. ABCDE ABCDE ABCDE ABCDE Replace the entire drum kit. Replace the transfer belt. Image defects cyclical (evenly spaced). Lateral image defects have 1­2 mm spacing. Lateral image defects have other spacing. Clean the laser lens cover. Replace the entire OPC drum kit. Solving Problems with Printing Quality 81 Symptom Abnormal areas (white or black belt or spots) appear. Cause The toner cartridge may be defective. The OPC drum cartridge may be defective or scratched. Solution Remove the toner cartridge and check for damage. Remove the OPC drum cartridge and check the photosensitive surface (the green surface) for scratches. If necessary, replace the entire drum kit. ABCDE ABCDE ABCDE ABCDE Lateral lines or bands appear on image. The fuser oil roller is dirty or Remove the fuser oil roller and check the roller surface for worn. Replace the fusing unit. Level the printer (not exceeding 1. 5° slant). If necessary, replace it. The fuser oil roller is dirty or Remove the fuser oil roller and check the roller surface for worn. Remove the OPC drum cartridge and check the green photosensitive surface for scratches. If necessary, replace it. 82 Solving Problems with Printing Quality Symptom Lateral lines appear cyclically (evenly spaced) on image. Cause Lateral lines have 1­2 mm spacing. Trailing edge 35 mm, other spacing Solution Replace the laser lens cover. Replace the fusing unit Replace the entire OPC drum kit. Vertical streaking appears. The laser lens cover may be Check to see if the laser lens cover is dirty. One or more toner cartridges The item may be defective or misinstalled. If a wide vertical white band appears, check the transfer belt surface. [. . . ] Impurities in the water may be released into the air, where they can accumulate inside the printer and cause degraded printer output. , , , , , , At an altitude of 0­8202' (0­2500 m). Near your computer--6. 5' (2 m) or less for an IEEE 1284 bidirectional parallel connection; cables for other connections may be longer. Close to an easily accessible grounded power supply on an exclusively dedicated power outlet. WARNING! Do not connect the groundwire to gas or water pipes or grounding for telephones. , , Not connected to the same electrical outlet as noise-generating equipment. If the printer is connected to the same circuit used by other high-current machines, such as a copier or air conditioner, or to an electrically noisy machine, low voltage or noise may cause overheating, computing errors resulting in data loss, and improper performance. [. . . ]