User manual MINOLTA MAGICOLOR 2 PLUS

[. . . ] ® ®  The following are trademarks or registered trademarks of their respective owners. Other product names mentioned in this manual may also be trademarks or registered trademarks of their respective owners. Registered trademarks are registered in the United States Patent and Trademark Office; some trademarks may also be registered in other countries. QMS, Crown, CrownAdmin, CrownNet, magicolor, the QMS logo, and the Crown seal are registered trademarks of QMS, Inc. , and CrownView, ImageServer, PS Executive Series, QCOLOR, and QFORM are trademarks of QMS, Inc. [. . . ] If not, go on to step 7. 7 » Plug in the printer, and turn it on. Note: In compliance with UL guidelines, "The appliance inlet is considered to be the main disconnect device. "  Caution: The OPC belt is extremely sensitive to touch. Always handle the cartridge so you don't touch the surface of the belt. Any body oil left on the surface of the belt will prevent toner from adhering to the belt which results in poor image quality. Also, keep the cartridge away from anything that may scratch the surface of the belt. Any scratches will show in the image produced. The OPC belt is also extremely sensitive to bright light and direct sunlight. Always leave it in its protective bag until you are ready to install it. If you suspect the belt is damaged due to exposure to light, put the belt in a dark place to recover. Depending on the amount of exposure, recovery may take up to two hours. Recovery is not guaranteed.  () #%  » Note: A dry cotton cloth is required for this procedure. If not, skip to step 3. 3 » Pull the latch to release the top cover, and then open the cover. Note: The illustrations for step 3 and step 4 show the printer without the duplexer. However, the instructions are the same for all models. 4 Open the printer's front cover, release the OPC belt cartridge green lock levers, and remove the OPC belt cartridge. %  ( () #%  5 Using a dry cotton cloth, clean any toner buildup from around the cleaning blade. Caution: Don't touch the edge of the cleaning blade. , 4 6 Clean any paper dust and toner buildup found on the OPC belt cartridge itself. " - 7 Caution: Handle the cartridge carefully. The belt is very sensitive to hand oils and scratches, both of which reduce print quality. Remove the corona wire cleaning brush from inside the front of the printer. 8 Turn the OPC belt cartridge so that the handle is facing away from you.  () #%  9 Use the brush to clean the corona wire inside end of the OPC belt cartridge. Do not press hard on the wire. 10 Reinstall the OPC belt cartridge, and secure its green lock levers. 11 Return the corona wire cleaning brush to its holder, and then close the printer's front and top covers. 12 If you have a duplexer, close the duplexer's rear cover. %  ( () #%  # #  It's necessary to clean the laser lens only when you find vertical white or light-color streaking in all primary colors on your printouts. A dry cotton cloth or dry cotton swab is required for this procedure. 1 2 3 Open the printer's front cover. Close the printer's front cover. If you have an EXD model, you should clean the inside of the duplexer on a regular basis. If not, skip to "Cleaning the Exterior of The Printer" on page 6-19.  () #%  2 3 Turn off and unplug the printer. Do not open the printer's rear cover. 4 Clean the duplexer with a dry cotton cloth. %  ( () #%  5 Tilt the paper path toward the inside of the printer. [. . . ] This ensures that no waste toner is shaken into the printer during shipment. 4 5 Close the printer's front and top covers. If you have a duplexer, close the duplexer's rear cover. (  529#3" 7 -'5* Caution: If you have an EXD (duplex) model, the lower input feeder must not be removed, even for shipping. If you don't have a lower input feeder installed on the CXE or DXE models, skip to "Repack the Printer" on page C-14. 1 » Remove the plastic side covers from the sides of the input feeder. [. . . ]