User manual MIELE W1070

[. . . ] This appliance is equipped with a cord having an equipmentgrounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances. WARNING - Improper connection of the equipment-grounding conductor may result in a risk of electric shock. Check with a qualified electrician if you are in doubt as to whether the appliance is properly grounded. [. . . ] Once the program has finished, the Child Lock must be deactivated. 20 Using the washer 9. shrink or discolor) during the next wash cycle. ^ Check the folds of the door seal for any small articles which may have been trapped. ^ Activate the Child Lock for safety reasons. , Children, animals or foreign objects may find their way into the drum. Danger of injury and damage to the machine! 21 Using the washer Canceling a program A program can be canceled any time after a program start. Interrupting a program ^ Press briefly the "Pause" button. ^ Press the "Pause" button until the "STATUS" indicator "Drain/Spin" indicator lights. Continue: ^ Press the "Start" button. Changing a program A program change is not possible after a program has started. To change a program, the program must be canceled first. Adjusting the temperature The temperature can be changed up to 6 minutes after the program start. Adjusting the spin speed The spin speed can be adjusted anytime until the beginning of the final spin. Changing an option The options "Extended or Sensitive" can be selected up to 6 minutes after the program start. The "Buzzer" can be selected or deselected at any time. 22 Using the washer Adding/removing laundry during a wash program The drum door cannot be opened if: ­ the water temperature is greater than 130°F (55°C). ­ The Child Lock function is activated. 23 Cleaning and Care , Before cleaning or maintenance, disconnect the power supply by unplugging the unit or manually "tripping" the circuit breaker. Cleaning the drum Germs can develop when using wash programs with a low temperature (below Hot) over several wash cycles. ^ Once a month run a program with no laundry using a "Hot" or "Sanitize" temperature and/or bleach. If the correct amount of detergent is dispensed, the machine should not need to be descaled. These filters should be checked and cleaned if necessary every 6 months. ^ Unscrew the inlet hose from the valve by turning the connector counterclockwise using a wrench if necessary. ^ Remove the rubber seal, 1, from the connector. ^ Using needle nose pliers, grasp the plastic filter, 2, and pull it out of the hose connector. ^ Clean the filter under running water and carefully remove any large particles. Both filters must be put back in place after cleaning. 28 Frequently asked questions , Repairs to electrical appliances must only be carried out by a qualified and trained person in accordance with local and national safety regulations. The manufacturer cannot be held responsible for unauthorized work. The following section will help you avoid placing a service call by identifying issues you may encounter while operating the machine: A wash program cannot be started Issue Possible cause Solution Check to determine if: ­ the washer is plugged in. A "PROGRAMS" The washer has no indicator does not light power. The "child entrapment sensor" has reacted. 29 Frequently asked questions The program was canceled, the buzzer sounds and the "Start" button flashes. Issue Possible cause Fix ­ To turn off the fault message: Open the drum door or press and hold the "Pause/Hold to Cancel" button until the fault message goes out. The "FAULT" indicator ­ The drain is "Drain" lights. The "FAULT" indicator The water intake is "Intake" lights. Call Technical Service. The "FAULT" indicators "Intake" and "Drain" light. The waterproof system has activated. The "STATUS" There is a fault. [. . . ] Replace the hose only with a genuine Mile hose, or with a hose able to withstand up to 145 psi (10 bar) pressure. The water valve connector must also be able to withstand 145 psi (10 bar). , The bolted connection is under water pressure. Adjust the rubber seal and the bolted connection if necessary. To protect the inlet valve, the two filters (one at the pressure hose / valve connection and one at the inlet connection to the solenoid valve) must not be removed. Hose extension (optional accessory) Hose extensions with a length of 8' 2 7/16" to 13' 1 ½" (2. 5 to 4 m) are available from your Mile dealer or Mile. 43 Plumbing Water connection ^ Connect the cold water intake hose (blue mark) to the cold water valve and the hot water intake hose (red mark) to the hot water valve. [. . . ]