User manual MIELE VACUUM CLEANER S280I EMERALD STAR

[. . . ] · Do not use to pick up flammable or combustible liquids such as gasoline or use in areas where they may be present. SAVE THESE INSTRUCTIONS THIS VACUUM CLEANER IS INTENDED FOR HOUSEHOLD USE ONLY Notice- Before you plug in your Vacuum Cleaner, make sure that the voltage indicated on the rating plate located at the rear of the vacuum cleaner is the same as your local supply. 2 IDENTIFICATION OF MAIN PARTS A-1) Handle B-2) Cord clip H) Bag change indicator D) Variable power control (S184 only) C) ON/OFF Switch Carry handle Dust bag cover J) Exhaust cover HEPA filter E) Foot pedal Bumper F) Beater bar selector A-3) Upper cord hook Cleaning head Head-light (S184 only) A-2) Hose clip B-1) Power cord I) Dust bag A-3) Lower cord hook/ Carrying handle Hose clip Extension tube Crevice nozzle Dusting brush Hose 3 HOW TO ASSEMBLE / OPERATE YOUR CLEANER A) HANDLE ASSEMBLY Upper cord hook Hose clip Lower cord hook/ Carrying handle 1) Insert the base of the handle into the top of the body of the machine as shown. IMPORTANT: Do not over tighten the screw. 2) Set the hose around the hose clip. 3) Turn the upper cord hook to the upright position and wind the power cord around the upper and lower cord hooks. B) POWER CORD STORAGE C) ON / OFF SWITCH 1) Turn the upper hook to release the power cord for instant use. 2) Set the power cord into the cord clip to help secure it during use To start or stop the vacuum cleaner, push the switch to "I" to turn it ON, and to "O" to turn it OFF. NOTE: To reduce the risk of electric shock, this appliance has a polarized plug (one blade is wider than the other). If it still does not fit, contact a qualified electrician to install the proper outlet. To avoid any possible damage to the power cord, never run over the cord or allow it to become caught in the rotary brush. 4 D) VARIABLE POWER CONTROL (S184 Only) This vacuum cleaner incorporates a variable power control to allow you to select the power most suitable for your cleaning needs. MIN: To clean curtains and soft furnishings with tool attached. MAX: To continuously clean with high suction power. E) USING THE FOOT PEDAL TO ADJUST THE VACUUM HEIGHT To lower the body of the cleaner, step on the pedal at the left rear corner of the vacuum cleaner. 1. [. . . ] To avoid any possible damage to the power cord, never run over the cord or allow it to become caught in the rotary brush. 4 D) VARIABLE POWER CONTROL (S184 Only) This vacuum cleaner incorporates a variable power control to allow you to select the power most suitable for your cleaning needs. MIN: To clean curtains and soft furnishings with tool attached. MAX: To continuously clean with high suction power. E) USING THE FOOT PEDAL TO ADJUST THE VACUUM HEIGHT To lower the body of the cleaner, step on the pedal at the left rear corner of the vacuum cleaner. 1. Upright position The handle should be in an upright position when cleaning tools are used. 2. Middle position For normal cleaning, press the foot pedal and pull back the handle to a comfortable angle. 3. Low position For cleaning under furniture, press the pedal a second time. The handle may now be lowered almost to the floor as shown. 5 F) BEATER BAR SELECTOR When cleaning carpeted floor, slide the selector to the "BEATER BAR" position. To stop the beater bar while using accessories, slide the selector to the "STOP" position. NOTE: The vacuum cleaner should be running when changing the position of the BEATER BAR SELECTOR. BEATER BAR ON OR OFF G) HOW TO USE THE ACCESSORIES 1) To use the accessories keep the vacuum cleaner upright and slide the BEATER BAR SELECTOR to the "STOP" position. 2) Pull the hose out of the intake port a the lower left of the vacuum, and release it from the hose clip. NOTE: When finished using the accessory, re-insert the hose end into the intake port and place the hose under the clip. 2 MAINTENANCE FOR THE BEATER BAR DO NOT USE YOUR FINGERS OR HANDS TO REMOVE OR CLEAN THE BEATER BAR. When it is necessary to remove thread, string, hair etc. , which has wound around the beater bar, cut across them with a pair of scissors, making sure not to cut the brush. REMOVE PLUG BEFORE REMOVING THIS COVER REMOVE PLUG BEFORE REMOVING THIS COVER 9 SERVICING AND REPAIRS Use only genuine Miele replacement parts. DISCONNECT THE CLEANER FROM THE ELECTRICAL SUPPLY If you have any questions, contact your local dealer / service agent. Any service needed other than that described in these Operating Instructions should be performed by a Miele Service Center, only. To replace any of the following parts, place the vacuum cleaner in the horizontal position by using the pedal. Then turn it over exposing the underside. HOW TO REPLACE - DRIVE BELT (Part # S01Z6000) AND BEATER BAR ASSEMBLY (Part # R98Z6064) 1. Release the belt from the motor shaft and lift the beater bar assembly to remove the belt. To reassemble the beater bar, return the belt to the motor shaft and beater bar pulley. Re-insert the bar into its supports and turn the beater bar to ensure that the belt is seated correctly. Replace the base plate, and re-fasten the screws securely. RE BEFO R VE PLUG IS CO VE TH REMO VING REMO Fig. 3 HOW TO REPLACE - BEATER BAR / SIDE BRUSHES / SHAFT SUPPORT A-B 1. [. . . ] Replace the base plate, and re-fasten the screws securely. RE BEFO R VE PLUG IS CO VE TH REMO VING REMO Fig. 3 HOW TO REPLACE - BEATER BAR / SIDE BRUSHES / SHAFT SUPPORT A-B 1. First remove the base plate, drive belt and beater bar assembly (as illustrated above). Remove the 2 screws at both ends of the beater bar assembly and separate the different parts as shown in the exploded view. [. . . ]