User manual MIELE T 369C VENT ED DRYER OPERATING MANUAL

[. . . ] Before this appliance is removed from service or discarded, remove the door to the drying compartment. Do not install or store this appliance where it will be exposed to the weather. Do not repair or replace any part of the appliance or attempt any servicing unless specifically recommended in these operating instructions. Repairs to electrical appliances should only be performed by qualified personnel. [. . . ] ^ Press and hold the "Buzzer" button until its indicator lights and you hear the desired volume and tone. 10 Using the dryer 6. At the end of a program The "Anti-crease/End" indicator will light at the end of a program and the buzzer will sound if it was selected. Once the program starts, the current cycle of the program will be indicated in the "STATUS" display. See "Frequently asked questions" for details. ^ Press the "Door" button. ^ Close the door. ^ Press the "On/Off" button to turn off the dryer. 11 Using the dryer Canceling or changing a program ^ Press and release the "Start/Stop T" button to stop the drying program. To continue drying: ^ Select the new program by pressing the e or - button. ^ Select a dryness level (available in the "Normal" and "Wrinkle-free" programs). ^ Press and release the "Start/Stop T" button to start the new program. Adding or removing laundry during a program ^ Turn off the dryer using the "On/Off" button. ^ Open the door. , CAUTION - Do not touch the rear of the drum while adding or removing items!^ Turn the dryer back on with the "On/Off" button. 12 Child lock Child lock When activated, the child lock prevents the dryer from being operated by locking the control panel functions. Press and hold the "Anti-crease" and "DRYNESS" buttons at the same time, hold until step 5. For items to be left damp for ironing. Note The "Extra Dry" program should not be selected for jersey materials. Items may shrink. Available drying options: Turbo, Full load, Gentle, Anti-crease More Dry Normal Less Dry Hand Iron Rotary Iron If items are still damp, dry again using "More Dry". If fabrics are too damp, dry again using "Less Dry". For items to be ironed with a rotary iron. For items which require ironing. To prevent moisture loss, roll up the laundry until ready to iron. Wrinkle-free Available drying options: Turbo, Gentle, Anti-crease More Dry Normal Less Dry Reduce load size for fabrics that wrinkle easily. Special Programs Available drying options: Anti-crease only available in Fluff, Sturdy Woolens Delicate items which allow machine drying. Take items out immediately after the end of the program while still slightly damp. Allow items to air dry. Smooth Sturdy Fluff - TIMED CYCLES Available drying options: Gentle, Anti-crease 20 min 30 min - Technical Service In the event of a fault you cannot fix yourself, please contact the Miele Technical Service Department U V 1-800-999-1360 techserv@mieleusa. com 1-800-565-6435 service@miele. ca PC Update The indicator on the control panel marked PC allows a technician to update the dryer to make use of new technology. For example, if new programs or fabrics are developed, a service technician will be able to modify the existing program cycles accordingly. When contacting Technical Service, please quote the model and serial number of your appliance. They can be found on the data plate located below the drum opening. 19 20 Installation Instructions IMPORTANT SAFETY INSTRUCTIONS Installation, repair and maintenance work should be performed by a Miele authorized service technician. Work by unqualified persons could be dangerous and could void the warranty. Before installation, disconnect the tumble dryer from the electrical supply by shutting off the power main, unplugging the power cord or tripping the circuit breaker. In the event of malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for electric current. This appliance is equipped with a cord having an equipment grounding conductor and a grounding plug. [. . . ] Minor discrepancies do not have an adverse effect on operation. 27 Installation Determining the position of the exhaust connection The exhaust connection can be left at the rear of the dryer (factory standard) or moved to the left or right side of the dryer. Changing the position of the exhaust connection ^ Remove the exhaust connection cover on the left or right side of the dryer. ^ Do this by inserting a screwdriver into each raised flap and lifting upwards, as shown. ^ Press the supplied cover firmly into the rear opening. ^ To remove the cap insert a screwdriver between the machine and the cap and lift upwards, the cap will then pop out of place. This cover is no longer needed. 28 Installation Installation tips An airflow gap of 3/8" (10 mm) must be provided between the machine and the floor. [. . . ]