User manual MIELE T 1526 VENT ED DRYER OPERATING MANUAL

[. . . ] Operations Manual for the T 1526 Vented Dryer It is essential to read these operating instructions before installing or using the machine to avoid the risk of accident, or damage to the machine. ö M. -Nr. 27 2 Guide to the machine Guide to the machine 1 2 3 4 5 Supply cable with plug Control panel Drum door Exhaust connection (left or rear) Four height-adjustable legs 3 Guide to the machine Pushbuttons ­ Door This button is used to open the door (does not stay pushed in). ­ j ON / k OFF When the machine is turned on, the "On" indicator will light up if the door is closed. ­ Buzzer Allows the buzzer to sound as the drum rotates during the anti-crease cycle. [. . . ] When selected the machine uses lower drying temperatures for delicate fabrics, (e. g. ­ Start Starts the selected program. "PROGRAM SEQUENCE" indicators The program sequence indicator lamps show the current status of the drying program. "DRYING STAGE REACHED" indicators This indicator shows which drying stage the program has reached. "PROGRAM SETTING" selector There is a range of settings for both "Cottons" and "Permanent Press". a cooling-cycle lasting 8 mins. ) or fluffed in cool air for 15 minutes. ­ Door This button is used to open the door. ­ ON/OFF When the machine is turned on, the "On" indicator lamp lights if the door is closed. ­ Buzzer When depressed, the buzzer will sound as the drum rotates during the anticrease cycle. 10 Program selection To select a program Press the "On/Off" button. To change a program during drying Set the program selector to the desired program. The tables on the following pages list the range of applications for the different programs. Set the desired program by turning the program selector either clockwise or counterclockwise. 7 lbs With blended fabrics consisting of wool and synthetics, consult the manufacturer's instructions, as the wool component may cause the fabric to matt and shrink. load Special instructions Normal 7 lbs Hand iron 7 lbs TIMED DRYING warm This cycle will run for the full 20 minutes, even if the clothes are dry sooner. - cool air 13 lbs 13 Cleaning and care Cleaning and care Cleaning the lint filter The lint is collected by the lint filter in the door. Clean the filter after every program. Cleaning the dryer Before cleaning the tumble dryer, disconnect the machine from the power supply. The dryer can be cleaned using soapy water or a mild non-abrasive detergent (not scouring powder) and dried with a soft cloth. The drum may be cleaned using a suitable stainless steel cleaner following the manufacturer's instructions. Do not hose down the machine or use abrasive cleaners. Grip the filter by the recessed handle and pull up to remove. Any lint remaining in the hollow part of the door can be removed through the gap at the bottom. Dry the lint filter before putting it back in place. 14 Problem solving guide Problem solving guide Electrical appliances should only be repaired by qualified personnel. There are, however, minor problems which can be corrected without contacting the Service Department. What to do if, . If so, failure to start may be due to an incorrect program selection procedure. If the "On" indicator lamp does not illuminate, check that: Remedy . Repeat the program selection procedure in the correct sequence, as outlined in the "Program Selection" chapter. ­ The machine is plugged in and the fuse or circuit breaker has not tripped. the "anti-crease" indicator lamp starts flashing? The load consisted of dissimilar items (size and fabrics). Small loads or individual items may cause the program to terminate prematurely. [. . . ] It should be pressed into the vent outlet and will simplify the connection of the exhaust pipe. Before installation, disconnect the tumble dryer from the electrical supply (unplug from the wall socket, or turn off the circuit breaker. Installation at the rear The machine comes supplied with the connector installed on the rear exhaust port. Installing the connector on the left side of the machine Remove the cap covering the exhaust part as follows: ­ Insert a thin screwdriver into the slot by the retaining hook. [. . . ]