User manual MIELE T 8013 C

[. . . ] Operating and Installation Instructions Condenser Dryer T 8012 C T 8013 C To prevent accidents and machine damage read these instructions before installation or use. UV M. -Nr. 34 2 IMPORTANT SAFETY INSTRUCTIONS , WARNING - To reduce the risk of fire, electric shock, or injury to persons when using your appliance, follow basic precautions, including the following: Read all instructions before using the appliance. Do not dry articles that have been previously cleaned, washed, soaked or spotted with gasoline, dry-cleaning solvents or other flammable or explosive substances. Close supervision is necessary when the appliance is used near children. [. . . ] Do not drink the condensed water! 16 Dryer care Cleaning the condenser , To reduce the risk of electric shock, disconnect the dryer from the power supply by shutting off the power main, tripping the circuit breaker or unplugging the power cord before performing maintenance. ^ Clean the condenser every 6 months and when the "Filter/Vent" indicator lights. Clean approximately every 100 uses when the dryer is used often. ^ Turn the condenser door lock down and remove the door up and out. Removing the condenser The access panel to the condenser is located on the lower left corner of the dryer. ^ Turn the condenser lock up. ^ Open the access panel with the supplied yellow tool. ^ Remove the panel up and out of the condenser access area. ^ Pull out the condenser. 17 Dryer care Rinsing the condenser Returning the Condenser ^ Put the condenser back in place in the reverse order. Check that the gasket around the front of the condenser is flush and not crimped. ^ To prevent leaks, make certain the condenser is pushed in all the way and locked in place. ^ Restore power. ^ Rinse the condenser along the left side with warm water. ^ Rinse the condenser from the front with warm water. ^ Place the condenser lengthwise on a towel to air dry. 18 Quick Guide Remove this guide for easy reference Please read all instructions, especially the "Important Safety Instructions", before using the dryer. Quick Guide 1. Turn on the dryer and load the laundry 2. Select a program ^ Press the "On/Off" button to turn on the dryer. ^ Press the "Door" button to open the door. Make sure that there is enough space in the drum for clothes to tumble freely. Select a drying option (if needed) To prevent fabric damage, check that laundry will not be caught in the closed door. ^ Close the door with a firm swing - do not push it shut. ^ A drying option can be selected or deselected with each press of the button. Quick Guide 4. At the end of a program The "Anti-crease / End" indicator will light. ^ Press the "On/Off" button to turn off the dryer. Quick Guide Program Normal Extra Dry When to use Available drying options Turbo, Gentle, Anti-crease For laundry to be folded and shelved immediately, e. g. For items to be left damp for ironing. Note The "Extra Dry" program should not be selected for jersey materials. Items may shrink. More Dry Normal Less Dry Hand Iron Rotary Iron If items are still damp, dry again using "More Dry". If fabrics are too damp, dry again using "Less Dry". For items to be ironed with a rotary iron. For items which require ironing. To prevent moisture loss, roll up the laundry until ready to iron. Wrinkle-free Available drying options Turbo, Gentle, Anti-crease More Dry Normal Less Dry Reduce load size for fabrics that wrinkle easily. Special Programs Available drying options: Anti-crease only available in Fluff, Sturdy Woolens Delicate items which allow machine drying. Take items out immediately after the end of the program while still slightly damp. Allow items to air dry. Smooth Sturdy Fluff - TIMED CYCLES 20 min 45 min Available drying options Gentle, Anti-crease - Dryer Care Changing the light bulb ^ Replace the light bulb with a temperature proof bulb, available from Miele. The light bulb must not exceed the maximum wattage listed on the data plate. ^ Flip up the light bulb cover and press it firmly until it clicks into place. , To reduce the risk of electric shock, disconnect the dryer from the power supply by shutting off the power main, tripping the circuit breaker or unplugging the power cord before performing maintenance. ^ Open the door. The bulb cover is located along the upper rim of the drum opening. , Make sure the bulb cover is securely closed to prevent a short circuit or penetrating moisture. ^ Restore power. ^ Slide a screwdriver with a wide head underneath the side edge of the bulb cover and twist (see illustration). [. . . ] It should be connected to a 120/208-240 V, 30 A, 60 Hz AC power supply. A 3 pole-4 wire grounding power outlet (NEMA type 14-30 R) is necessary. 27 Installation Front view a Power cord with plug b Condensed water container c Control panel d Door e Access panel to condenser f Four height adjustable feet g Optional drain hose: An alternative to using the condensed water container is to drain condensed water into a sink, standpipe or gully. 28 Installation Rear view Installation site , Do not install the dryer in an area where it can be blocked, e. g. behind a door. , This appliance is not intended to be mounted in a wall or other vertical surface of a building or cabinet. Transporting the dryer to the installation site a Handle for transportation (arrows) b Air intake opening to cool the condenser c Power cord with plug d Condensate drain hose e Accessories for connection to a sink standpipe The rear excess end of the lid has a handle box for transport. [. . . ]