User manual MIELE T 1403

[. . . ] Operating Instructions Vented Dryer T 1403 To prevent accidents and machine damage, read these instructions before Installation or use. UV M. -Nr. 31 2 IMPORTANT SAFETY INSTRUCTIONS , WARNING - To reduce the risk of Do not repair or replace any part of the appliance or attempt any servicing unless specifically recommended in these operating instructions. Repairs to electrical appliances should only be performed by qualified personnel. Incorrectly repaired machines may pose a considerable risk to the user. [. . . ] The light bulb must not exceed the maximum wattage listed on the data plate. ^ Flip up the light bulb cover and press it firmly until it clicks into place. , To reduce the risk of electric shock, disconnect the dryer from the power supply by shutting off the power main, tripping the circuit breaker or unplugging the power cord before performing maintenance. ^ Open the door. The bulb cover is located along the upper rim of the drum opening. , Make sure the bulb cover is ^ Restore power. securely closed to prevent a short circuit or penetrating moisture. ^ Slide a screwdriver with a wide head underneath the side edge of the bulb cover and twist (see illustration). ^ Flip down the bulb cover. 16 Frequently asked questions What if the dryer will not run? Possible fault Fix The "Start/Stop T" button was not pressed. Press the "Start/ Stop T" button to begin the drying program. Close the door properly. Add fabric softener to laundry when washing or select the "Less Dry" setting on the dryer. What if the drum light does not come on? Possible fault Fix The bulb may be bad or burned out. See "Changing the light bulb. " What if the "Child Lock" indicator flashes after turning the dryer on and a program cannot be started? Possible fault Fix The child lock is activated. Deactivate the child lock. See "Child Lock. " What if the program stops, the "Anti-crease / End" indicator lights and the buzzer sounds? Possible fault Fix The drum is empty. Load laundry into the dryer. Single items should be dried with "Sturdy" or a timed program and dry items in the "Fluff" program. What if the "Filter/Vent" fault indicator is lit? Possible fault Fix The lint filter is clogged. The air supply in the room is insufficient. Clean the lint filters. Open a window or door to increase airflow. 17 Frequently asked questions What if the "Filter/Vent" indicator lights after cleaning the exhaust system? Possible fault Fix The dryer is not operating efficiently because the duct hose is too long. Check the exhaust length and diameter (see "How to calculate the effective duct length"). A long exhaust hose will increase program times and energy consumption. If the exhaust hose cannot be shortened, the indicator can be turned off by a service technician. What if the program runs too long or stops? Possible fault Fix The airflow is insufficient in the area of the dryer. The lint filters are clogged. Open a window or door to increase airflow. Clean the lint filters (see "Dryer care"). The laundry was not spun sufficiently in Select a higher spin speed in the wash the washer. Select a timed program to avoid overdrying. An airflow gap of 3/8" (10 mm) must be This gap must not be blocked by a provided between the machine and the toekick or thick piled carpets for sufficient airflow. What if the laundry is not dry enough? Possible fault The load contained too many dissimilar items (size and fabric. ) What if water has collected around the drum opening? Possible fault This is condensed moisture from the laundry. 18 Quick Guide Remove this guide for easy reference Please read all instructions, especially the "Important Safety Instructions", before using the dryer. Quick Guide 1. Turn on the dryer and load the laundry 2. Select a program ^ Press the "On/Off" button to turn on the dryer. ^ Press the "Door" button to open the door. Make sure that there is enough space in the drum for clothes to tumble freely. Select a drying option (if needed) To prevent fabric damage, check that laundry will not be caught in the closed door. ^ Close the door with a firm swing - do not push it shut. ^ A drying option can be selected or deselected with each press of the button. Quick Guide 4. Select the dryness level ^ Press the selection button until the desired indicator illuminates. [. . . ] A 3 pole-4 wire grounding power outlet (NEMA type 14-30 R) is necessary. EASY INSTALLATION KIT If you do not have a dedicated 15 Amp line for this appliance, but you have the standard, 120/208-240 V - 30 Amp, 60 Hz AC outlet, you can use the "Easy Installation Kit", which allows you to use that line to connect the dryer to power. 057B for on-site outlet NEMA 10-30 R 060B for on-site outlet NEMA 14-30 R For more information on the "Easy Installation Kit" or if you have questions concerning the electrical connection, please contact: U V 1-800-999-1360 techserv@mieleusa. com 1-800-565-6435 service@miele. ca 25 Installation a Exhaust connection: The exhaust hose can be installed either at the rear, left or right of the dryer. b Power cord with plug c Control panel d Door e Four height adjustable feet 26 Installation Leveling the dryer Determining the position of the exhaust connection The exhaust connection can be left at the rear of the dryer (factory standard) or moved to the left or right side of the dryer. [. . . ]