User manual MIELE T 8685 C

[. . . ] Operating instructions for condenser tumble dryer T 8685 C To avoid the risk of accidents or damage to the machine it is essential to read these instructions before it is installed and used for the first time. G M. -Nr. 06 731 760 Caring for the environment Disposal of the packing material The transport and protective packing has been selected from materials which are environmentally friendly for disposal and can normally be recycled. are disposed of safely and kept out of the reach of babies and young children. Rather than just throwing these materials away, please ensure they are offered for recycling. [. . . ] Weight of dry laundry 27 Changing the programme sequence Changing a programme while it Interrupting a programme is running ^ Switch the tumble dryer off by You cannot change to another programme once a programme has started (this prevents unintentional alterations). You will need to cancel the current programme before you can select a new one. To continue drying ^ Switch the tumble dryer on again by pressing the s button. The programme will continue, as long as the cooling down phase has not been reached. Cancelling a programme ^ Press short cut button 4 Cancel. The items will be cooled down, depending on the temperature reached and how long they have been dried for. Adding or removing laundry after a programme has started ^ Press the a button. ^ Open the door. Finish will appear when you press short cut button 4 Cancel again. ^ Switch the tumble dryer off by pressing the s button. ^ Select a different programme. , Do not touch the back of the drum when adding or removing items. ^ Press the Start button. Note The time remaining shown in the display may now vary from the actual drying time. 28 Electronic programme locking Programme locking prevents the short cut buttons or the multi-function selector being used while drying is in progress. To activate programme locking ^ Once the programme has begun, press and hold the Start button until the following appears in the display: X System locked Now no more alterations can be made to the programme. Programme locking is deactivated automatically at the end of the programme or by pressing button a. To deactivate programme locking ^ Press and hold the Start button until the following appears in the display: W Ready 29 Cleaning and care Emptying the condensed water container The condensed water will be collected in the condensed water container unless the appliance has been fitted with a drain hose (see installation). The drying programme will be interrupted if the maximum level of the condensed water container is reached. A message will appear in the display. ^ Open the shutter and empty out the water. ^ To replace the container, hold it at a slight angle (as when removing it) and push it in gently until you feel it click into position. ^ To remove the message from the display, switch the dryer off and then on again. To ensure that any residual particles of fluff in the condensed water are removed before use, pass it through a fine sieve or paper filter first. ^ Holding the container firmly in both hands, as shown, pull it out slightly towards the right-hand side. ^ Hold the container in a horizontal position when carrying it. 30 Cleaning and care Cleaning the fluff filters The fluff which is created by the drying process is collected by the fluff filters in the door and the door opening. Cleaning them whilst dry Tip: You can also use a vacuum cleaner to remove the fluff. ^ Use your fingers to remove the fluff from the surface of the filter. You could also use a cleaning brush which is available as an optional extra from your Miele dealer or the Miele Spare Parts Department, or use a vacuum cleaner. ^ Once clean, push the filter back into the door holder until it clicks into position. Ensure it is facing the correct way. ^ Open the door and pull the fluff filter (1) out of the door as illustrated. ^ Use your fingers or a vacuum cleaner to remove the fluff from the two fluff filters in the door opening. [. . . ] There are two options: Active (the machine is delivered with this option selected) Standby is activated: ­ if a programme is not selected 10 minutes after the machine has been switched on. Not in current programme Standby is activated: ­ if a programme is not selected 10 minutes after the machine has been switched on. Operating the multi-function selector or one of the short cut buttons switches the display back on again. A tick L will appear beside the option to show that it has been set. 60 Settings menu J The following settings only appear if Communication module XKM 2000 has been fitted to the dryer. Mieleqhome This communication enabled dryer can transmit programme data through the power lines to the Miele|home system. [. . . ]